Browse Inventory |
Recalls |
About Us |
Contact Us |
Privacy |
Terms of Use |
Sitemap
|
|
|
|
|
|
Browse Inventory |
Recalls |
About Us |
Contact Us |
Privacy |
Terms of Use |
Sitemap
|
|
|
| |
Automobile Manufacturer Recall Data - Mercedes Recalls 
Posted: 06-14-2011 | |
| 550 G-CLASS C C CLASS C-CLASS CL CL CLASS CL-600 CL215 CL216 CLK CLK CLASS CLS CLS CLASS E E CLASS G CLASS G55 GL M M CLASS M-CLASS ML R R CLASS R-CLASS S S CLASS S-600 S220 S221 SL CLASS SL230 SLK SLR MCLAREN | |
| 550 G-CLASS RECALLS | Top |
| 2009 MERCEDES 550 G-CLASS Manufactured between: 09/01/2008 and 05/30/2009 Defect: mercedes-benz is recalling model year 2009 550 g-class vehicles. the fuel line quick connectors located under the vehicle away from the engine compartment may not have been connected properly on the assembly line and completely seated in the connection. in case of a frontal crash, the fuel pump would no longer function but a partial dislocation of the line could lead to a potential for fuel loss from the line at the quick connector. Consequence: fuel leakage, in the presence of an ignition source, could result in a fire. Action: dealers will check the connection of the fuel line quick connectors and install a new clamp to assure the quick connectors secure connection. the remedy will be performed free of charge. the safety recall is expected to begin during january 2010. owners may contact mercedes-benz at 1-800-367-6372. Recall Date: 11/24/2009 | |
| C RECALLS | Top |
| 2010 MERCEDES C Manufactured between: 06/01/2009 and 02/28/2010 Defect: mercedes benz is recalling certain model year 2010 c-class, model 204, e-class, model 212, and model year 2010-2011 e-class coupe/cabriolet model 207 vehicles. the power steering system in the subject vehicles may fail due to the loss of power steering fluid. Consequence: owners may not have sufficient control of the vehicle in areas, such as parking lots, where maximum power steering is required, increasing the risk of a vehicle crash. Action: dealers will check and retorque the connection fitting free of charge. the safety recall began on october 31, 2010. owners may contact mercedes-benz at 1-800-367-6372. Recall Date: 10/04/2010 | |
| 2008 MERCEDES C Manufactured between: 05/01/2007 and 05/31/2008 Defect: mercedes-benz is recalling my 2006-2008 m-class, r-class, my 2005-2009 slk-class, my 2005-2008 c-class, my 2003-2004 and 2006-2008 clk-class, my 2003-2008 e-class, my 2004 and 2008 cl-class, my 2008 cls-class, my 2004 and 2007-2008 s-class, my 2003 g-class, and my 2003-2004, 2006 and 2009 sl-class vehicles. a software calibration number (scn) coding received on the affected vehicles during a recent workshop visit was incorrect. depending on the model year and model affected, the results of an incorrect scn coding can affect a number of vehicle safety and emission functions including the following types of functions: (1) the fuel gauge readings may be incorrect; (2) a stuck fuel-level sensor may not be displayed in the instrument cluster; (3) the obd system may cause the check engine light to illuminate incorrectly; and, (4) the speedometer may be out of tolerance. Consequence: in the event of a vehicle crash, the electrical fuel pump may not receive a crash signal that is required for the fuel pump to disconnect and prevent future fuel delivery as designed. Action: dealers will recode the scn free of charge. the recall began on august 30, 2008. owners may contact mercedes-benz at 1-800-367-6372. Recall Date: 07/07/2008 | |
| 2007 MERCEDES C Manufactured between: 08/01/2004 and 01/31/2007 Defect: mercedes-benz is recalling my 2006-2008 m-class, r-class, my 2005-2009 slk-class, my 2005-2008 c-class, my 2003-2004 and 2006-2008 clk-class, my 2003-2008 e-class, my 2004 and 2008 cl-class, my 2008 cls-class, my 2004 and 2007-2008 s-class, my 2003 g-class, and my 2003-2004, 2006 and 2009 sl-class vehicles. a software calibration number (scn) coding received on the affected vehicles during a recent workshop visit was incorrect. depending on the model year and model affected, the results of an incorrect scn coding can affect a number of vehicle safety and emission functions including the following types of functions: (1) the fuel gauge readings may be incorrect; (2) a stuck fuel-level sensor may not be displayed in the instrument cluster; (3) the obd system may cause the check engine light to illuminate incorrectly; and, (4) the speedometer may be out of tolerance. Consequence: in the event of a vehicle crash, the electrical fuel pump may not receive a crash signal that is required for the fuel pump to disconnect and prevent future fuel delivery as designed. Action: dealers will recode the scn free of charge. the recall began on august 30, 2008. owners may contact mercedes-benz at 1-800-367-6372. Recall Date: 07/07/2008 | |
| C CLASS RECALLS | Top |
| 2006 MERCEDES C CLASS Manufactured between: 08/01/2004 and 01/31/2007 Defect: mercedes-benz is recalling my 2006-2008 m-class, r-class, my 2005-2009 slk-class, my 2005-2008 c-class, my 2003-2004 and 2006-2008 clk-class, my 2003-2008 e-class, my 2004 and 2008 cl-class, my 2008 cls-class, my 2004 and 2007-2008 s-class, my 2003 g-class, and my 2003-2004, 2006 and 2009 sl-class vehicles. a software calibration number (scn) coding received on the affected vehicles during a recent workshop visit was incorrect. depending on the model year and model affected, the results of an incorrect scn coding can affect a number of vehicle safety and emission functions including the following types of functions: (1) the fuel gauge readings may be incorrect; (2) a stuck fuel-level sensor may not be displayed in the instrument cluster; (3) the obd system may cause the check engine light to illuminate incorrectly; and, (4) the speedometer may be out of tolerance. Consequence: in the event of a vehicle crash, the electrical fuel pump may not receive a crash signal that is required for the fuel pump to disconnect and prevent future fuel delivery as designed. Action: dealers will recode the scn free of charge. the recall began on august 30, 2008. owners may contact mercedes-benz at 1-800-367-6372. Recall Date: 07/07/2008 | |
| 2006 MERCEDES C CLASS Manufactured between: 05/01/2004 and 11/30/2005 Defect: certain passenger vehicles equipped with sport model steering wheels fail to comply with the requirements of federal motor vehicle safety standard no. 208, "occupant crash protection." in certain low risk air bag deployment tests conducted by nhtsa, using an out-of-position unbelted 5th percentile female crash test dummy, irregularities were demonstrated indicating that occupants may not be properly protected in a crash. Consequence: in the event of a crash, an occupant may not be properly restrained which could result in injuries. Action: dealers will install a new air bag inflator module free of charge. the recall began on march 15, 2006. owners may contact mercedes-benz at 1-800-367-6372. Recall Date: 12/20/2005 | |
| 2005 MERCEDES C CLASS Manufactured between: 08/01/2004 and 01/31/2007 Defect: mercedes-benz is recalling my 2006-2008 m-class, r-class, my 2005-2009 slk-class, my 2005-2008 c-class, my 2003-2004 and 2006-2008 clk-class, my 2003-2008 e-class, my 2004 and 2008 cl-class, my 2008 cls-class, my 2004 and 2007-2008 s-class, my 2003 g-class, and my 2003-2004, 2006 and 2009 sl-class vehicles. a software calibration number (scn) coding received on the affected vehicles during a recent workshop visit was incorrect. depending on the model year and model affected, the results of an incorrect scn coding can affect a number of vehicle safety and emission functions including the following types of functions: (1) the fuel gauge readings may be incorrect; (2) a stuck fuel-level sensor may not be displayed in the instrument cluster; (3) the obd system may cause the check engine light to illuminate incorrectly; and, (4) the speedometer may be out of tolerance. Consequence: in the event of a vehicle crash, the electrical fuel pump may not receive a crash signal that is required for the fuel pump to disconnect and prevent future fuel delivery as designed. Action: dealers will recode the scn free of charge. the recall began on august 30, 2008. owners may contact mercedes-benz at 1-800-367-6372. Recall Date: 07/07/2008 | |
| 2005 MERCEDES C CLASS Manufactured between: 05/01/2004 and 11/30/2005 Defect: certain passenger vehicles equipped with sport model steering wheels fail to comply with the requirements of federal motor vehicle safety standard no. 208, "occupant crash protection." in certain low risk air bag deployment tests conducted by nhtsa, using an out-of-position unbelted 5th percentile female crash test dummy, irregularities were demonstrated indicating that occupants may not be properly protected in a crash. Consequence: in the event of a crash, an occupant may not be properly restrained which could result in injuries. Action: dealers will install a new air bag inflator module free of charge. the recall began on march 15, 2006. owners may contact mercedes-benz at 1-800-367-6372. Recall Date: 12/20/2005 | |
| 2004 MERCEDES C CLASS Manufactured between: 08/01/2003 and 10/31/2003 Defect: on certain passenger vehicles, some seat belt buckles may have a burr on a metal component of the locking mechanism. the presence of the burr could prevent the seat belt from locking under certain circumstances. Consequence: in the event of a crash, the seat occupant may not be properly restrained, increasing the risk of injury. Action: dealers will replace the seat belts. owner notification began on december 22, 2003. owners should contact mercedes-benz at 1-800-367-6372. Recall Date: 12/19/2003 | |
| C-CLASS RECALLS | Top |
| 2008 MERCEDES C-CLASS Manufactured between: 05/01/2007 and 08/31/2007 Defect: certain vehicles fail to comply with some of the requirements of federal motor vehicle safety standard no. 208, "occupant crash protection." the rear outboard seat belts do not comply with the lap-belt lockability requirement which enables the lap belt portion of the belt to be locked by the user to facilitate the use of older non-latch design child restraint devices. Consequence: under certain circumstances, this situation may cause the locking mechanism not to perform as required by the standard for use with older non-latch child restraints. Action: dealers will replace all potentially affected seat belts. the recall began on november 19, 2007. owners may contact mercedes-benz at 1-800-367-6372. Recall Date: 10/03/2007 | |
| CL RECALLS | Top |
| 2008 MERCEDES CL Manufactured between: 04/01/2007 and 03/31/2008 Defect: mercedes-benz is recalling my 2006-2008 m-class, r-class, my 2005-2009 slk-class, my 2005-2008 c-class, my 2003-2004 and 2006-2008 clk-class, my 2003-2008 e-class, my 2004 and 2008 cl-class, my 2008 cls-class, my 2004 and 2007-2008 s-class, my 2003 g-class, and my 2003-2004, 2006 and 2009 sl-class vehicles. a software calibration number (scn) coding received on the affected vehicles during a recent workshop visit was incorrect. depending on the model year and model affected, the results of an incorrect scn coding can affect a number of vehicle safety and emission functions including the following types of functions: (1) the fuel gauge readings may be incorrect; (2) a stuck fuel-level sensor may not be displayed in the instrument cluster; (3) the obd system may cause the check engine light to illuminate incorrectly; and, (4) the speedometer may be out of tolerance. Consequence: in the event of a vehicle crash, the electrical fuel pump may not receive a crash signal that is required for the fuel pump to disconnect and prevent future fuel delivery as designed. Action: dealers will recode the scn free of charge. the recall began on august 30, 2008. owners may contact mercedes-benz at 1-800-367-6372. Recall Date: 07/07/2008 | |
| 2008 MERCEDES CL Manufactured between: 10/27/2007 and 12/31/2007 Defect: mercedes-benz is recalling 3,283 my 2008 s-class and cl-class passenger vehicles. a malfunction may occur on the signal acquisition and actuation module-front (sam-f) transistors. the sam-f is a double transistor that helps control vehicle functions and the lighting of the center console. incorrect storage of the transistors led the transistors to be exposed to excess humidity. Consequence: the presence of this moisture in combination with the thermal stress during the "reflow soldering" may damage the transistors and prevent them from properly functioning which will increase the risk of crash. Action: dealers will inspect and replace all potentially affected sam free of charge. the recall began on may 2, 2008. owner may contact mercedes benz at 1-800-367-6372. Recall Date: 03/19/2008 | |
| 2008 MERCEDES CL Manufactured between: 10/27/2007 and 12/31/2007 Defect: mercedes-benz is recalling 3,283 my 2008 s-class and cl-class passenger vehicles. a malfunction may occur on the signal acquisition and actuation module-front (sam-f) transistors. the sam-f is a double transistor that helps control vehicle functions and the lighting of the center console. incorrect storage of the transistors led the transistors to be exposed to excess humidity. Consequence: the presence of this moisture in combination with the thermal stress during the "reflow soldering" may damage the transistors and prevent them from properly functioning which will increase the risk of crash. Action: dealers will inspect and replace all potentially affected sam free of charge. the recall began on may 2, 2008. owner may contact mercedes benz at 1-800-367-6372. Recall Date: 03/19/2008 | |
| CL CLASS RECALLS | Top |
| 2005 MERCEDES CL CLASS Manufactured between: 05/01/2004 and 09/30/2004 Defect: on certain vehicles, the instrument cluster is experiencing electrical malfunctions. the instrument cluster contains gauges and indicators that must be illuminated whenever the vehicle is in operation. Consequence: due to inadequate illumination, the driver will be unable to read the gauges and indicators, such as the speedometer, which could increase the risk of a crash. Action: dealers will replace the instrument cluster modules. the recall will be conducted in phases. phase i was mailed out to approximately 7,500 owners on september 29, 2006. phase ii and phase iii is scheduled for december 2006. owners may contact mercedes-benz at 1-800-367-6372. Recall Date: 02/02/2006 | |
| 2004 MERCEDES CL CLASS Manufactured between: 05/01/2004 and 05/31/2004 Defect: mercedes-benz is recalling my 2006-2008 m-class, r-class, my 2005-2009 slk-class, my 2005-2008 c-class, my 2003-2004 and 2006-2008 clk-class, my 2003-2008 e-class, my 2004 and 2008 cl-class, my 2008 cls-class, my 2004 and 2007-2008 s-class, my 2003 g-class, and my 2003-2004, 2006 and 2009 sl-class vehicles. a software calibration number (scn) coding received on the affected vehicles during a recent workshop visit was incorrect. depending on the model year and model affected, the results of an incorrect scn coding can affect a number of vehicle safety and emission functions including the following types of functions: (1) the fuel gauge readings may be incorrect; (2) a stuck fuel-level sensor may not be displayed in the instrument cluster; (3) the obd system may cause the check engine light to illuminate incorrectly; and, (4) the speedometer may be out of tolerance. Consequence: in the event of a vehicle crash, the electrical fuel pump may not receive a crash signal that is required for the fuel pump to disconnect and prevent future fuel delivery as designed. Action: dealers will recode the scn free of charge. the recall began on august 30, 2008. owners may contact mercedes-benz at 1-800-367-6372. Recall Date: 07/07/2008 | |
| 2004 MERCEDES CL CLASS Manufactured between: 05/01/2004 and 09/30/2004 Defect: on certain vehicles, the instrument cluster is experiencing electrical malfunctions. the instrument cluster contains gauges and indicators that must be illuminated whenever the vehicle is in operation. Consequence: due to inadequate illumination, the driver will be unable to read the gauges and indicators, such as the speedometer, which could increase the risk of a crash. Action: dealers will replace the instrument cluster modules. the recall will be conducted in phases. phase i was mailed out to approximately 7,500 owners on september 29, 2006. phase ii and phase iii is scheduled for december 2006. owners may contact mercedes-benz at 1-800-367-6372. Recall Date: 02/02/2006 | |
| 2004 MERCEDES CL CLASS Manufactured between: 05/01/2003 and 10/31/2003 Defect: on certain vehicles, the trunk lid springs could fail in the closed trunk lid position. Consequence: if the trunk lid is manually lifted, it may not remain in the up position and could cause injury if it comes down while someone is reaching into the trunk. Action: dealers will replace both trunk lid springs. the recall began august 17, 2004. owners should contact mercedes- benz at 1-800-367-6372. Recall Date: 06/09/2004 | |
| CL-600 RECALLS | Top |
| 2004 MERCEDES CL-600 Manufactured between: 12/01/1999 and 03/31/2004 Defect: on certain passenger vehicles, corrosion may occur in the inner steel portions of the active body control's (abc) high-pressure distribution hose due to extensive exposure to heat and humidity. over time, corrosion may deteriorate the inner steel portions of the hose. Consequence: this may result in abc hydraulic fluid leakage. under some circumstances, leaking hydraulic fluid may come in contact with hot engine components and lead to a possibility of fire. Action: dealers will install new, corrosion resistant abc high-pressure distribution hoses. the recall began august 31, 2004. owners should contact mercedes-benz at 1-800-367-6372. Recall Date: 05/13/2004 | |
| CL215 RECALLS | Top |
| 2006 MERCEDES CL215 Manufactured between: 09/01/2000 and 09/30/2005 Defect: mercedes benz is recalling 4,564 my 2001-2006 cl-class (model 215), my 2002-2006 s-class (model 220), my 2003-2007 sl-class (model 230), my 2007-2008 cl-class (model 216), and my 2007 s-class (model 221)passenger vehicles equipped with active body control (abc) acceleration sensors on the front struts. these sensors measure acceleration around the z-axis of the vehicle and assure an automatic adaptation of the front struts to maintain a relatively level body position. variations in the soldering process resulted in soldering points on the board of the abc sensors which may not be within design tolerances. signals from the affected sensors measuring the acceleration may not be accurately transmitted to the engine control unit. Consequence: a variation in the transmitted values between affected and unaffected sensors can result in one front strut adjusting to a value indicating body movement while another strut does not adjust presenting the driver with an uneven front suspension. this condition may lead to unexpected body movements at the front axle which can adversely influence the vehicle's directional stability and could lead to a vehicle crash. Action: dealers will inspect and replace, if necessary, the front abc sensors in all potentially affected vehicles. the recall began on september 22, 2008. owners may contact mercedes-benz at 1-800-367-6372. Recall Date: 08/14/2008 | |
| 2005 MERCEDES CL215 Manufactured between: 09/01/2000 and 09/30/2005 Defect: mercedes benz is recalling 4,564 my 2001-2006 cl-class (model 215), my 2002-2006 s-class (model 220), my 2003-2007 sl-class (model 230), my 2007-2008 cl-class (model 216), and my 2007 s-class (model 221)passenger vehicles equipped with active body control (abc) acceleration sensors on the front struts. these sensors measure acceleration around the z-axis of the vehicle and assure an automatic adaptation of the front struts to maintain a relatively level body position. variations in the soldering process resulted in soldering points on the board of the abc sensors which may not be within design tolerances. signals from the affected sensors measuring the acceleration may not be accurately transmitted to the engine control unit. Consequence: a variation in the transmitted values between affected and unaffected sensors can result in one front strut adjusting to a value indicating body movement while another strut does not adjust presenting the driver with an uneven front suspension. this condition may lead to unexpected body movements at the front axle which can adversely influence the vehicle's directional stability and could lead to a vehicle crash. Action: dealers will inspect and replace, if necessary, the front abc sensors in all potentially affected vehicles. the recall began on september 22, 2008. owners may contact mercedes-benz at 1-800-367-6372. Recall Date: 08/14/2008 | |
| 2004 MERCEDES CL215 Manufactured between: 09/01/2000 and 09/30/2005 Defect: mercedes benz is recalling 4,564 my 2001-2006 cl-class (model 215), my 2002-2006 s-class (model 220), my 2003-2007 sl-class (model 230), my 2007-2008 cl-class (model 216), and my 2007 s-class (model 221)passenger vehicles equipped with active body control (abc) acceleration sensors on the front struts. these sensors measure acceleration around the z-axis of the vehicle and assure an automatic adaptation of the front struts to maintain a relatively level body position. variations in the soldering process resulted in soldering points on the board of the abc sensors which may not be within design tolerances. signals from the affected sensors measuring the acceleration may not be accurately transmitted to the engine control unit. Consequence: a variation in the transmitted values between affected and unaffected sensors can result in one front strut adjusting to a value indicating body movement while another strut does not adjust presenting the driver with an uneven front suspension. this condition may lead to unexpected body movements at the front axle which can adversely influence the vehicle's directional stability and could lead to a vehicle crash. Action: dealers will inspect and replace, if necessary, the front abc sensors in all potentially affected vehicles. the recall began on september 22, 2008. owners may contact mercedes-benz at 1-800-367-6372. Recall Date: 08/14/2008 | |
| CL216 RECALLS | Top |
| 2008 MERCEDES CL216 Manufactured between: 10/01/2006 and 04/30/2007 Defect: mercedes benz is recalling 4,564 my 2001-2006 cl-class (model 215), my 2002-2006 s-class (model 220), my 2003-2007 sl-class (model 230), my 2007-2008 cl-class (model 216), and my 2007 s-class (model 221)passenger vehicles equipped with active body control (abc) acceleration sensors on the front struts. these sensors measure acceleration around the z-axis of the vehicle and assure an automatic adaptation of the front struts to maintain a relatively level body position. variations in the soldering process resulted in soldering points on the board of the abc sensors which may not be within design tolerances. signals from the affected sensors measuring the acceleration may not be accurately transmitted to the engine control unit. Consequence: a variation in the transmitted values between affected and unaffected sensors can result in one front strut adjusting to a value indicating body movement while another strut does not adjust presenting the driver with an uneven front suspension. this condition may lead to unexpected body movements at the front axle which can adversely influence the vehicle's directional stability and could lead to a vehicle crash. Action: dealers will inspect and replace, if necessary, the front abc sensors in all potentially affected vehicles. the recall began on september 22, 2008. owners may contact mercedes-benz at 1-800-367-6372. Recall Date: 08/14/2008 | |
| 2007 MERCEDES CL216 Manufactured between: 10/01/2006 and 04/30/2007 Defect: mercedes benz is recalling 4,564 my 2001-2006 cl-class (model 215), my 2002-2006 s-class (model 220), my 2003-2007 sl-class (model 230), my 2007-2008 cl-class (model 216), and my 2007 s-class (model 221)passenger vehicles equipped with active body control (abc) acceleration sensors on the front struts. these sensors measure acceleration around the z-axis of the vehicle and assure an automatic adaptation of the front struts to maintain a relatively level body position. variations in the soldering process resulted in soldering points on the board of the abc sensors which may not be within design tolerances. signals from the affected sensors measuring the acceleration may not be accurately transmitted to the engine control unit. Consequence: a variation in the transmitted values between affected and unaffected sensors can result in one front strut adjusting to a value indicating body movement while another strut does not adjust presenting the driver with an uneven front suspension. this condition may lead to unexpected body movements at the front axle which can adversely influence the vehicle's directional stability and could lead to a vehicle crash. Action: dealers will inspect and replace, if necessary, the front abc sensors in all potentially affected vehicles. the recall began on september 22, 2008. owners may contact mercedes-benz at 1-800-367-6372. Recall Date: 08/14/2008 | |
| CLK RECALLS | Top |
| 2008 MERCEDES CLK Manufactured between: 05/01/2003 and 11/30/2007 Defect: mercedes-benz is recalling my 2006-2008 m-class, r-class, my 2005-2009 slk-class, my 2005-2008 c-class, my 2003-2004 and 2006-2008 clk-class, my 2003-2008 e-class, my 2004 and 2008 cl-class, my 2008 cls-class, my 2004 and 2007-2008 s-class, my 2003 g-class, and my 2003-2004, 2006 and 2009 sl-class vehicles. a software calibration number (scn) coding received on the affected vehicles during a recent workshop visit was incorrect. depending on the model year and model affected, the results of an incorrect scn coding can affect a number of vehicle safety and emission functions including the following types of functions: (1) the fuel gauge readings may be incorrect; (2) a stuck fuel-level sensor may not be displayed in the instrument cluster; (3) the obd system may cause the check engine light to illuminate incorrectly; and, (4) the speedometer may be out of tolerance. Consequence: in the event of a vehicle crash, the electrical fuel pump may not receive a crash signal that is required for the fuel pump to disconnect and prevent future fuel delivery as designed. Action: dealers will recode the scn free of charge. the recall began on august 30, 2008. owners may contact mercedes-benz at 1-800-367-6372. Recall Date: 07/07/2008 | |
| 2007 MERCEDES CLK Manufactured between: 05/01/2003 and 11/30/2007 Defect: mercedes-benz is recalling my 2006-2008 m-class, r-class, my 2005-2009 slk-class, my 2005-2008 c-class, my 2003-2004 and 2006-2008 clk-class, my 2003-2008 e-class, my 2004 and 2008 cl-class, my 2008 cls-class, my 2004 and 2007-2008 s-class, my 2003 g-class, and my 2003-2004, 2006 and 2009 sl-class vehicles. a software calibration number (scn) coding received on the affected vehicles during a recent workshop visit was incorrect. depending on the model year and model affected, the results of an incorrect scn coding can affect a number of vehicle safety and emission functions including the following types of functions: (1) the fuel gauge readings may be incorrect; (2) a stuck fuel-level sensor may not be displayed in the instrument cluster; (3) the obd system may cause the check engine light to illuminate incorrectly; and, (4) the speedometer may be out of tolerance. Consequence: in the event of a vehicle crash, the electrical fuel pump may not receive a crash signal that is required for the fuel pump to disconnect and prevent future fuel delivery as designed. Action: dealers will recode the scn free of charge. the recall began on august 30, 2008. owners may contact mercedes-benz at 1-800-367-6372. Recall Date: 07/07/2008 | |
| CLK CLASS RECALLS | Top |
| 2006 MERCEDES CLK CLASS Manufactured between: 05/01/2003 and 11/30/2007 Defect: mercedes-benz is recalling my 2006-2008 m-class, r-class, my 2005-2009 slk-class, my 2005-2008 c-class, my 2003-2004 and 2006-2008 clk-class, my 2003-2008 e-class, my 2004 and 2008 cl-class, my 2008 cls-class, my 2004 and 2007-2008 s-class, my 2003 g-class, and my 2003-2004, 2006 and 2009 sl-class vehicles. a software calibration number (scn) coding received on the affected vehicles during a recent workshop visit was incorrect. depending on the model year and model affected, the results of an incorrect scn coding can affect a number of vehicle safety and emission functions including the following types of functions: (1) the fuel gauge readings may be incorrect; (2) a stuck fuel-level sensor may not be displayed in the instrument cluster; (3) the obd system may cause the check engine light to illuminate incorrectly; and, (4) the speedometer may be out of tolerance. Consequence: in the event of a vehicle crash, the electrical fuel pump may not receive a crash signal that is required for the fuel pump to disconnect and prevent future fuel delivery as designed. Action: dealers will recode the scn free of charge. the recall began on august 30, 2008. owners may contact mercedes-benz at 1-800-367-6372. Recall Date: 07/07/2008 | |
| 2004 MERCEDES CLK CLASS Manufactured between: 05/01/2003 and 11/30/2007 Defect: mercedes-benz is recalling my 2006-2008 m-class, r-class, my 2005-2009 slk-class, my 2005-2008 c-class, my 2003-2004 and 2006-2008 clk-class, my 2003-2008 e-class, my 2004 and 2008 cl-class, my 2008 cls-class, my 2004 and 2007-2008 s-class, my 2003 g-class, and my 2003-2004, 2006 and 2009 sl-class vehicles. a software calibration number (scn) coding received on the affected vehicles during a recent workshop visit was incorrect. depending on the model year and model affected, the results of an incorrect scn coding can affect a number of vehicle safety and emission functions including the following types of functions: (1) the fuel gauge readings may be incorrect; (2) a stuck fuel-level sensor may not be displayed in the instrument cluster; (3) the obd system may cause the check engine light to illuminate incorrectly; and, (4) the speedometer may be out of tolerance. Consequence: in the event of a vehicle crash, the electrical fuel pump may not receive a crash signal that is required for the fuel pump to disconnect and prevent future fuel delivery as designed. Action: dealers will recode the scn free of charge. the recall began on august 30, 2008. owners may contact mercedes-benz at 1-800-367-6372. Recall Date: 07/07/2008 | |
| 2004 MERCEDES CLK CLASS Manufactured between: 08/01/2003 and 10/31/2003 Defect: on certain passenger vehicles, some seat belt buckles may have a burr on a metal component of the locking mechanism. the presence of the burr could prevent the seat belt from locking under certain circumstances. Consequence: in the event of a crash, the seat occupant may not be properly restrained, increasing the risk of injury. Action: dealers will replace the seat belts. owner notification began on december 22, 2003. owners should contact mercedes-benz at 1-800-367-6372. Recall Date: 12/19/2003 | |
| CLS RECALLS | Top |
| 2008 MERCEDES CLS Manufactured between: 09/01/2007 and 11/30/2007 Defect: mercedes-benz is recalling my 2006-2008 m-class, r-class, my 2005-2009 slk-class, my 2005-2008 c-class, my 2003-2004 and 2006-2008 clk-class, my 2003-2008 e-class, my 2004 and 2008 cl-class, my 2008 cls-class, my 2004 and 2007-2008 s-class, my 2003 g-class, and my 2003-2004, 2006 and 2009 sl-class vehicles. a software calibration number (scn) coding received on the affected vehicles during a recent workshop visit was incorrect. depending on the model year and model affected, the results of an incorrect scn coding can affect a number of vehicle safety and emission functions including the following types of functions: (1) the fuel gauge readings may be incorrect; (2) a stuck fuel-level sensor may not be displayed in the instrument cluster; (3) the obd system may cause the check engine light to illuminate incorrectly; and, (4) the speedometer may be out of tolerance. Consequence: in the event of a vehicle crash, the electrical fuel pump may not receive a crash signal that is required for the fuel pump to disconnect and prevent future fuel delivery as designed. Action: dealers will recode the scn free of charge. the recall began on august 30, 2008. owners may contact mercedes-benz at 1-800-367-6372. Recall Date: 07/07/2008 | |
| CLS CLASS RECALLS | Top |
| 2006 MERCEDES CLS CLASS Manufactured between: 03/01/2004 and 03/31/2005 Defect: on certain vehicles, the sensotronic brake control (sbc) system may prematurely shift to the hydraulic back-up function mode, due to deterioration of the wiring harness connection, or due to premature failure of the hydraulic pump. Consequence: in the hydraulic back-up mode, the driver has braking power sufficient to stop the vehicle, although greater brake pedal pressure is required and the brake pedal travel will be noticeably longer. Action: dealers will install a bracket and replacement ground wire to the sbc pump unit on all vehicles free of charge. additionally dealers will inspect and replace the sbc pump unit in sl vehicles produced during a limited production period. the recall began on august 8, 2005. owners may contact mercedes-benz at 1-800-367-6372. Recall Date: 04/01/2005 | |
| E RECALLS | Top |
| 2011 MERCEDES E Manufactured between: 07/08/2010 and 07/12/2010 Defect: mercedes-benz is recalling certain model year 2011 e-class model w212 and s212 vehicles manufactured from july 8, 2010, through july 12, 2010. insufficient adhesive between the vibration damper and its inner mass damper ring could cause a sudden separation of the inner mass damper ring from the vibration damper. Consequence: while working in the engine compartment during engine operation, the damper ring could strike and injure the person repairing the vehicle or a bystander. Action: dealers will inspect and replace parts as necessary free of charge. the safety recall began on april 8, 2011. owners may contact mercedes-benz at 1-800-367-6372. Recall Date: 04/01/2011 | |
| 2011 MERCEDES E Manufactured between: 07/01/2010 and 09/30/2010 Defect: mercedes benz is recalling certain model year 2011 m-class, model w164, gl-class, model x164, e-class, model w212, r-class, and model v251vehicles. the o-ring may not have been properly lubricated in all cases. lack of lubrication can lead to leakage of the fuel filter. Consequence: diesel fuel may be deposited on roads and making those roads slippery, increasing the potential for a crash. Action: dealers will replace the fuel filters free of charge. the safety recall began on november 24, 2010. owners may contact mercedes benz at 1-800-367-6372. Recall Date: 10/29/2010 | |
| 2011 MERCEDES E Manufactured between: 06/01/2009 and 02/28/2010 Defect: mercedes benz is recalling certain model year 2010 c-class, model 204, e-class, model 212, and model year 2010-2011 e-class coupe/cabriolet model 207 vehicles. the power steering system in the subject vehicles may fail due to the loss of power steering fluid. Consequence: owners may not have sufficient control of the vehicle in areas, such as parking lots, where maximum power steering is required, increasing the risk of a vehicle crash. Action: dealers will check and retorque the connection fitting free of charge. the safety recall began on october 31, 2010. owners may contact mercedes-benz at 1-800-367-6372. Recall Date: 10/04/2010 | |
| 2010 MERCEDES E Manufactured between: 06/01/2009 and 02/28/2010 Defect: mercedes benz is recalling certain model year 2010 c-class, model 204, e-class, model 212, and model year 2010-2011 e-class coupe/cabriolet model 207 vehicles. the power steering system in the subject vehicles may fail due to the loss of power steering fluid. Consequence: owners may not have sufficient control of the vehicle in areas, such as parking lots, where maximum power steering is required, increasing the risk of a vehicle crash. Action: dealers will check and retorque the connection fitting free of charge. the safety recall began on october 31, 2010. owners may contact mercedes-benz at 1-800-367-6372. Recall Date: 10/04/2010 | |
| 2008 MERCEDES E Manufactured between: 11/01/2002 and 10/31/2007 Defect: mercedes-benz is recalling my 2006-2008 m-class, r-class, my 2005-2009 slk-class, my 2005-2008 c-class, my 2003-2004 and 2006-2008 clk-class, my 2003-2008 e-class, my 2004 and 2008 cl-class, my 2008 cls-class, my 2004 and 2007-2008 s-class, my 2003 g-class, and my 2003-2004, 2006 and 2009 sl-class vehicles. a software calibration number (scn) coding received on the affected vehicles during a recent workshop visit was incorrect. depending on the model year and model affected, the results of an incorrect scn coding can affect a number of vehicle safety and emission functions including the following types of functions: (1) the fuel gauge readings may be incorrect; (2) a stuck fuel-level sensor may not be displayed in the instrument cluster; (3) the obd system may cause the check engine light to illuminate incorrectly; and, (4) the speedometer may be out of tolerance. Consequence: in the event of a vehicle crash, the electrical fuel pump may not receive a crash signal that is required for the fuel pump to disconnect and prevent future fuel delivery as designed. Action: dealers will recode the scn free of charge. the recall began on august 30, 2008. owners may contact mercedes-benz at 1-800-367-6372. Recall Date: 07/07/2008 | |
| 2008 MERCEDES E Manufactured between: 05/01/2006 and 10/31/2007 Defect: on certain passenger vehicles equipped with diesel engines, the crankshaft sensor could fail due to separation of bond wires from the lead frame in the sensor. this results in an interruption in the electrical connection in the chip housing of the sensor. Consequence: when this happens, the vehicle may lose power rather than enter a limp-home mode. in addition, the vehicle cannot be restarted after failure of the electrical connection in the sensor, increasing the risk of a crash. Action: dealers will replace the crankshaft sensor. the recall began on february 4, 2008. owners may contact mercedes-benz at 1-800-367-6372. Recall Date: 01/09/2008 | |
| 2007 MERCEDES E Manufactured between: 11/01/2002 and 10/31/2007 Defect: mercedes-benz is recalling my 2006-2008 m-class, r-class, my 2005-2009 slk-class, my 2005-2008 c-class, my 2003-2004 and 2006-2008 clk-class, my 2003-2008 e-class, my 2004 and 2008 cl-class, my 2008 cls-class, my 2004 and 2007-2008 s-class, my 2003 g-class, and my 2003-2004, 2006 and 2009 sl-class vehicles. a software calibration number (scn) coding received on the affected vehicles during a recent workshop visit was incorrect. depending on the model year and model affected, the results of an incorrect scn coding can affect a number of vehicle safety and emission functions including the following types of functions: (1) the fuel gauge readings may be incorrect; (2) a stuck fuel-level sensor may not be displayed in the instrument cluster; (3) the obd system may cause the check engine light to illuminate incorrectly; and, (4) the speedometer may be out of tolerance. Consequence: in the event of a vehicle crash, the electrical fuel pump may not receive a crash signal that is required for the fuel pump to disconnect and prevent future fuel delivery as designed. Action: dealers will recode the scn free of charge. the recall began on august 30, 2008. owners may contact mercedes-benz at 1-800-367-6372. Recall Date: 07/07/2008 | |
| 2007 MERCEDES E Manufactured between: 05/01/2006 and 10/31/2007 Defect: on certain passenger vehicles equipped with diesel engines, the crankshaft sensor could fail due to separation of bond wires from the lead frame in the sensor. this results in an interruption in the electrical connection in the chip housing of the sensor. Consequence: when this happens, the vehicle may lose power rather than enter a limp-home mode. in addition, the vehicle cannot be restarted after failure of the electrical connection in the sensor, increasing the risk of a crash. Action: dealers will replace the crankshaft sensor. the recall began on february 4, 2008. owners may contact mercedes-benz at 1-800-367-6372. Recall Date: 01/09/2008 | |
| 2006 MERCEDES E Manufactured between: 05/01/2006 and 10/31/2007 Defect: on certain passenger vehicles equipped with diesel engines, the crankshaft sensor could fail due to separation of bond wires from the lead frame in the sensor. this results in an interruption in the electrical connection in the chip housing of the sensor. Consequence: when this happens, the vehicle may lose power rather than enter a limp-home mode. in addition, the vehicle cannot be restarted after failure of the electrical connection in the sensor, increasing the risk of a crash. Action: dealers will replace the crankshaft sensor. the recall began on february 4, 2008. owners may contact mercedes-benz at 1-800-367-6372. Recall Date: 01/09/2008 | |
| E CLASS RECALLS | Top |
| 2006 MERCEDES E CLASS Manufactured between: 11/01/2002 and 10/31/2007 Defect: mercedes-benz is recalling my 2006-2008 m-class, r-class, my 2005-2009 slk-class, my 2005-2008 c-class, my 2003-2004 and 2006-2008 clk-class, my 2003-2008 e-class, my 2004 and 2008 cl-class, my 2008 cls-class, my 2004 and 2007-2008 s-class, my 2003 g-class, and my 2003-2004, 2006 and 2009 sl-class vehicles. a software calibration number (scn) coding received on the affected vehicles during a recent workshop visit was incorrect. depending on the model year and model affected, the results of an incorrect scn coding can affect a number of vehicle safety and emission functions including the following types of functions: (1) the fuel gauge readings may be incorrect; (2) a stuck fuel-level sensor may not be displayed in the instrument cluster; (3) the obd system may cause the check engine light to illuminate incorrectly; and, (4) the speedometer may be out of tolerance. Consequence: in the event of a vehicle crash, the electrical fuel pump may not receive a crash signal that is required for the fuel pump to disconnect and prevent future fuel delivery as designed. Action: dealers will recode the scn free of charge. the recall began on august 30, 2008. owners may contact mercedes-benz at 1-800-367-6372. Recall Date: 07/07/2008 | |
| 2005 MERCEDES E CLASS Manufactured between: 11/01/2002 and 10/31/2007 Defect: mercedes-benz is recalling my 2006-2008 m-class, r-class, my 2005-2009 slk-class, my 2005-2008 c-class, my 2003-2004 and 2006-2008 clk-class, my 2003-2008 e-class, my 2004 and 2008 cl-class, my 2008 cls-class, my 2004 and 2007-2008 s-class, my 2003 g-class, and my 2003-2004, 2006 and 2009 sl-class vehicles. a software calibration number (scn) coding received on the affected vehicles during a recent workshop visit was incorrect. depending on the model year and model affected, the results of an incorrect scn coding can affect a number of vehicle safety and emission functions including the following types of functions: (1) the fuel gauge readings may be incorrect; (2) a stuck fuel-level sensor may not be displayed in the instrument cluster; (3) the obd system may cause the check engine light to illuminate incorrectly; and, (4) the speedometer may be out of tolerance. Consequence: in the event of a vehicle crash, the electrical fuel pump may not receive a crash signal that is required for the fuel pump to disconnect and prevent future fuel delivery as designed. Action: dealers will recode the scn free of charge. the recall began on august 30, 2008. owners may contact mercedes-benz at 1-800-367-6372. Recall Date: 07/07/2008 | |
| 2005 MERCEDES E CLASS Manufactured between: 08/01/2001 and 03/31/2005 Defect: on certain vehicles, the sensotronic brake control (sbc) system may prematurely shift to the hydraulic back-up function mode, due to deterioration of the wiring harness connection, or due to premature failure of the hydraulic pump. Consequence: in the hydraulic back-up mode, the driver has braking power sufficient to stop the vehicle, although greater brake pedal pressure is required and the brake pedal travel will be noticeably longer. Action: dealers will install a bracket and replacement ground wire to the sbc pump unit on all vehicles free of charge. additionally dealers will inspect and replace the sbc pump unit in sl vehicles produced during a limited production period. the recall began on august 8, 2005. owners may contact mercedes-benz at 1-800-367-6372. Recall Date: 04/01/2005 | |
| 2004 MERCEDES E CLASS Manufactured between: 11/01/2002 and 10/31/2007 Defect: mercedes-benz is recalling my 2006-2008 m-class, r-class, my 2005-2009 slk-class, my 2005-2008 c-class, my 2003-2004 and 2006-2008 clk-class, my 2003-2008 e-class, my 2004 and 2008 cl-class, my 2008 cls-class, my 2004 and 2007-2008 s-class, my 2003 g-class, and my 2003-2004, 2006 and 2009 sl-class vehicles. a software calibration number (scn) coding received on the affected vehicles during a recent workshop visit was incorrect. depending on the model year and model affected, the results of an incorrect scn coding can affect a number of vehicle safety and emission functions including the following types of functions: (1) the fuel gauge readings may be incorrect; (2) a stuck fuel-level sensor may not be displayed in the instrument cluster; (3) the obd system may cause the check engine light to illuminate incorrectly; and, (4) the speedometer may be out of tolerance. Consequence: in the event of a vehicle crash, the electrical fuel pump may not receive a crash signal that is required for the fuel pump to disconnect and prevent future fuel delivery as designed. Action: dealers will recode the scn free of charge. the recall began on august 30, 2008. owners may contact mercedes-benz at 1-800-367-6372. Recall Date: 07/07/2008 | |
| 2004 MERCEDES E CLASS Manufactured between: 08/01/2001 and 03/31/2005 Defect: on certain vehicles, the sensotronic brake control (sbc) system may prematurely shift to the hydraulic back-up function mode, due to deterioration of the wiring harness connection, or due to premature failure of the hydraulic pump. Consequence: in the hydraulic back-up mode, the driver has braking power sufficient to stop the vehicle, although greater brake pedal pressure is required and the brake pedal travel will be noticeably longer. Action: dealers will install a bracket and replacement ground wire to the sbc pump unit on all vehicles free of charge. additionally dealers will inspect and replace the sbc pump unit in sl vehicles produced during a limited production period. the recall began on august 8, 2005. owners may contact mercedes-benz at 1-800-367-6372. Recall Date: 04/01/2005 | |
| 2004 MERCEDES E CLASS Manufactured between: 10/01/2001 and 05/31/2004 Defect: on certain vehicles, the electronic monitoring system of the sensotronic brake control (sbc) is designed to monitor the pressure gradient within the high pressure line of the brake system. if an unacceptable pressure gradient is detected, the system will switch, as it is designed to do, into the hydraulic function mode. Consequence: if vehicles are not routinely serviced and have extremely high mileage combined with a high number of brake actuations, or a high brake actuation frequency, the pump motor of the sbc may run out of permissible tolerances, thereby triggering the hydraulic function mode. Action: dealers will inspect the sbc hydraulic unit, replacing it if necessary. the recall began on october 21m 2004. owners should contact mercedes-benz at 1-800-367-6372. Recall Date: 06/22/2004 | |
| 2004 MERCEDES E CLASS Manufactured between: 08/01/2003 and 10/31/2003 Defect: on certain passenger vehicles, some seat belt buckles may have a burr on a metal component of the locking mechanism. the presence of the burr could prevent the seat belt from locking under certain circumstances. Consequence: in the event of a crash, the seat occupant may not be properly restrained, increasing the risk of injury. Action: dealers will replace the seat belts. owner notification began on december 22, 2003. owners should contact mercedes-benz at 1-800-367-6372. Recall Date: 12/19/2003 | |
| G CLASS RECALLS | Top |
| 2010 MERCEDES G CLASS Manufactured between: 09/01/2002 and 07/30/2010 Defect: mercedes-benz is recalling certain model year 2002-2010 g-class vehicles for failing to comply with the requirements of federal motor vehicle safety standard no. 108, "'lamps, reflective devices, and associated equipment." these vehicles are equipped with a grill cover for front turn signal protection that, while permissible, may impact over time the signal's ability to meet the minimum requirements of fmvss 108. Consequence: the signal light's visibility to other motorists may be reduced over time, increasing the risk of a crash. Action: dealers will install improved turn light units optimized for usage with grills. this service will be performed free of charge. the safety recall is expected to begin at the end of december 2010 or early january 2011. owners may contact mercedes-benz at 1-800-367-6372. Recall Date: 08/05/2010 | |
| 2009 MERCEDES G CLASS Manufactured between: 09/01/2002 and 07/30/2010 Defect: mercedes-benz is recalling certain model year 2002-2010 g-class vehicles for failing to comply with the requirements of federal motor vehicle safety standard no. 108, "'lamps, reflective devices, and associated equipment." these vehicles are equipped with a grill cover for front turn signal protection that, while permissible, may impact over time the signal's ability to meet the minimum requirements of fmvss 108. Consequence: the signal light's visibility to other motorists may be reduced over time, increasing the risk of a crash. Action: dealers will install improved turn light units optimized for usage with grills. this service will be performed free of charge. the safety recall is expected to begin at the end of december 2010 or early january 2011. owners may contact mercedes-benz at 1-800-367-6372. Recall Date: 08/05/2010 | |
| 2008 MERCEDES G CLASS Manufactured between: 09/01/2002 and 07/30/2010 Defect: mercedes-benz is recalling certain model year 2002-2010 g-class vehicles for failing to comply with the requirements of federal motor vehicle safety standard no. 108, "'lamps, reflective devices, and associated equipment." these vehicles are equipped with a grill cover for front turn signal protection that, while permissible, may impact over time the signal's ability to meet the minimum requirements of fmvss 108. Consequence: the signal light's visibility to other motorists may be reduced over time, increasing the risk of a crash. Action: dealers will install improved turn light units optimized for usage with grills. this service will be performed free of charge. the safety recall is expected to begin at the end of december 2010 or early january 2011. owners may contact mercedes-benz at 1-800-367-6372. Recall Date: 08/05/2010 | |
| 2007 MERCEDES G CLASS Manufactured between: 09/01/2002 and 07/30/2010 Defect: mercedes-benz is recalling certain model year 2002-2010 g-class vehicles for failing to comply with the requirements of federal motor vehicle safety standard no. 108, "'lamps, reflective devices, and associated equipment." these vehicles are equipped with a grill cover for front turn signal protection that, while permissible, may impact over time the signal's ability to meet the minimum requirements of fmvss 108. Consequence: the signal light's visibility to other motorists may be reduced over time, increasing the risk of a crash. Action: dealers will install improved turn light units optimized for usage with grills. this service will be performed free of charge. the safety recall is expected to begin at the end of december 2010 or early january 2011. owners may contact mercedes-benz at 1-800-367-6372. Recall Date: 08/05/2010 | |
| 2006 MERCEDES G CLASS Manufactured between: 09/01/2002 and 07/30/2010 Defect: mercedes-benz is recalling certain model year 2002-2010 g-class vehicles for failing to comply with the requirements of federal motor vehicle safety standard no. 108, "'lamps, reflective devices, and associated equipment." these vehicles are equipped with a grill cover for front turn signal protection that, while permissible, may impact over time the signal's ability to meet the minimum requirements of fmvss 108. Consequence: the signal light's visibility to other motorists may be reduced over time, increasing the risk of a crash. Action: dealers will install improved turn light units optimized for usage with grills. this service will be performed free of charge. the safety recall is expected to begin at the end of december 2010 or early january 2011. owners may contact mercedes-benz at 1-800-367-6372. Recall Date: 08/05/2010 | |
| 2005 MERCEDES G CLASS Manufactured between: 09/01/2002 and 07/30/2010 Defect: mercedes-benz is recalling certain model year 2002-2010 g-class vehicles for failing to comply with the requirements of federal motor vehicle safety standard no. 108, "'lamps, reflective devices, and associated equipment." these vehicles are equipped with a grill cover for front turn signal protection that, while permissible, may impact over time the signal's ability to meet the minimum requirements of fmvss 108. Consequence: the signal light's visibility to other motorists may be reduced over time, increasing the risk of a crash. Action: dealers will install improved turn light units optimized for usage with grills. this service will be performed free of charge. the safety recall is expected to begin at the end of december 2010 or early january 2011. owners may contact mercedes-benz at 1-800-367-6372. Recall Date: 08/05/2010 | |
| 2004 MERCEDES G CLASS Manufactured between: 09/01/2002 and 07/30/2010 Defect: mercedes-benz is recalling certain model year 2002-2010 g-class vehicles for failing to comply with the requirements of federal motor vehicle safety standard no. 108, "'lamps, reflective devices, and associated equipment." these vehicles are equipped with a grill cover for front turn signal protection that, while permissible, may impact over time the signal's ability to meet the minimum requirements of fmvss 108. Consequence: the signal light's visibility to other motorists may be reduced over time, increasing the risk of a crash. Action: dealers will install improved turn light units optimized for usage with grills. this service will be performed free of charge. the safety recall is expected to begin at the end of december 2010 or early january 2011. owners may contact mercedes-benz at 1-800-367-6372. Recall Date: 08/05/2010 | |
| G55 RECALLS | Top |
| 2005 MERCEDES G55 Manufactured between: 04/01/2005 and 04/30/2005 Defect: on certain sport utility vehicles, the fuel return hose between fuel tank and return line can be permeated with fuel. this situation results from the expansion and contraction of the hose under pressure causing microcracks in the hose material. Consequence: these microcracks may cause fuel leakage. fuel leakage in the presence of an ignition source could result in a fire. Action: dealers will inspect and replace all fuel return hoses with the appropriate hoses free of charge. the recall began on september 27, 2005. owners may contact mercedes benz at 1-800-367-6372. Recall Date: 08/29/2005 | |
| 2004 MERCEDES G55 Manufactured between: 04/01/2005 and 04/30/2005 Defect: on certain sport utility vehicles, the fuel return hose between fuel tank and return line can be permeated with fuel. this situation results from the expansion and contraction of the hose under pressure causing microcracks in the hose material. Consequence: these microcracks may cause fuel leakage. fuel leakage in the presence of an ignition source could result in a fire. Action: dealers will inspect and replace all fuel return hoses with the appropriate hoses free of charge. the recall began on september 27, 2005. owners may contact mercedes benz at 1-800-367-6372. Recall Date: 08/29/2005 | |
| GL RECALLS | Top |
| 2011 MERCEDES GL Manufactured between: 03/01/2010 and 10/31/2010 Defect: mercedes benz is recalling certain model year 2011 m-class, model w164, gl-class, model x164, e-class, model w212, r-class, and model v251vehicles. the o-ring may not have been properly lubricated in all cases. lack of lubrication can lead to leakage of the fuel filter. Consequence: diesel fuel may be deposited on roads and making those roads slippery, increasing the potential for a crash. Action: dealers will replace the fuel filters free of charge. the safety recall began on november 24, 2010. owners may contact mercedes benz at 1-800-367-6372. Recall Date: 10/29/2010 | |
| 2008 MERCEDES GL Manufactured between: 03/03/2008 and 03/20/2008 Defect: mercedes-benz is recalling 577 my 2008 gl-class, m-class, and r-class vehicles. a defect may exist in the driving pin used to control the oil pressure of the power steering. Consequence: if a defective driving pin exists in a vehicle and the pin breaks during normal vehicle turning, the normally available hydraulic support function will no longer function and steering wheel operation will be limited. Action: mercedes-benz will replace the steering gears. the recall began on january 28, 2009. owner may contact mercedes-benz at 1-800-367-6372. Recall Date: 12/19/2008 | |
| 2008 MERCEDES GL Manufactured between: 07/01/2006 and 04/30/2008 Defect: mercedes-benz is recalling 52,740 my 2006-2008 gl and ml class vehicles equipped with flex-n-gate trailer hitch. some of the weld seams connecting the trailer hitch receiver to the attachment bar used to secure the trailer hitch to the body frame do not meet performance specifications. Consequence: this may result in the traile rhitch receiver separating from the attachment bar, creating a road hazard which may lead to a vehicle crash. the trailer hitch must not be used for any purpose until it has been repaired. Action: dealers will repair the trailer hitch. the recall began on june 16, 2008. owenrs may contact mercedes-benz at 1-800-367-6372. Recall Date: 06/02/2008 | |
| 2008 MERCEDES GL Manufactured between: 05/01/2006 and 10/31/2007 Defect: on certain passenger vehicles equipped with diesel engines, the crankshaft sensor could fail due to separation of bond wires from the lead frame in the sensor. this results in an interruption in the electrical connection in the chip housing of the sensor. Consequence: when this happens, the vehicle may lose power rather than enter a limp-home mode. in addition, the vehicle cannot be restarted after failure of the electrical connection in the sensor, increasing the risk of a crash. Action: dealers will replace the crankshaft sensor. the recall began on february 4, 2008. owners may contact mercedes-benz at 1-800-367-6372. Recall Date: 01/09/2008 | |
| 2007 MERCEDES GL Manufactured between: 07/01/2006 and 04/30/2008 Defect: mercedes-benz is recalling 52,740 my 2006-2008 gl and ml class vehicles equipped with flex-n-gate trailer hitch. some of the weld seams connecting the trailer hitch receiver to the attachment bar used to secure the trailer hitch to the body frame do not meet performance specifications. Consequence: this may result in the traile rhitch receiver separating from the attachment bar, creating a road hazard which may lead to a vehicle crash. the trailer hitch must not be used for any purpose until it has been repaired. Action: dealers will repair the trailer hitch. the recall began on june 16, 2008. owenrs may contact mercedes-benz at 1-800-367-6372. Recall Date: 06/02/2008 | |
| 2007 MERCEDES GL Manufactured between: 05/01/2006 and 10/31/2007 Defect: on certain passenger vehicles equipped with diesel engines, the crankshaft sensor could fail due to separation of bond wires from the lead frame in the sensor. this results in an interruption in the electrical connection in the chip housing of the sensor. Consequence: when this happens, the vehicle may lose power rather than enter a limp-home mode. in addition, the vehicle cannot be restarted after failure of the electrical connection in the sensor, increasing the risk of a crash. Action: dealers will replace the crankshaft sensor. the recall began on february 4, 2008. owners may contact mercedes-benz at 1-800-367-6372. Recall Date: 01/09/2008 | |
| 2006 MERCEDES GL Manufactured between: 07/01/2006 and 04/30/2008 Defect: mercedes-benz is recalling 52,740 my 2006-2008 gl and ml class vehicles equipped with flex-n-gate trailer hitch. some of the weld seams connecting the trailer hitch receiver to the attachment bar used to secure the trailer hitch to the body frame do not meet performance specifications. Consequence: this may result in the traile rhitch receiver separating from the attachment bar, creating a road hazard which may lead to a vehicle crash. the trailer hitch must not be used for any purpose until it has been repaired. Action: dealers will repair the trailer hitch. the recall began on june 16, 2008. owenrs may contact mercedes-benz at 1-800-367-6372. Recall Date: 06/02/2008 | |
| 2006 MERCEDES GL Manufactured between: 05/01/2006 and 10/31/2007 Defect: on certain passenger vehicles equipped with diesel engines, the crankshaft sensor could fail due to separation of bond wires from the lead frame in the sensor. this results in an interruption in the electrical connection in the chip housing of the sensor. Consequence: when this happens, the vehicle may lose power rather than enter a limp-home mode. in addition, the vehicle cannot be restarted after failure of the electrical connection in the sensor, increasing the risk of a crash. Action: dealers will replace the crankshaft sensor. the recall began on february 4, 2008. owners may contact mercedes-benz at 1-800-367-6372. Recall Date: 01/09/2008 | |
| M RECALLS | Top |
| 2011 MERCEDES M Manufactured between: 03/01/2010 and 10/31/2010 Defect: mercedes benz is recalling certain model year 2011 m-class, model w164, gl-class, model x164, e-class, model w212, r-class, and model v251vehicles. the o-ring may not have been properly lubricated in all cases. lack of lubrication can lead to leakage of the fuel filter. Consequence: diesel fuel may be deposited on roads and making those roads slippery, increasing the potential for a crash. Action: dealers will replace the fuel filters free of charge. the safety recall began on november 24, 2010. owners may contact mercedes benz at 1-800-367-6372. Recall Date: 10/29/2010 | |
| M CLASS RECALLS | Top |
| 2008 MERCEDES M CLASS Manufactured between: 03/03/2008 and 03/20/2008 Defect: mercedes-benz is recalling 577 my 2008 gl-class, m-class, and r-class vehicles. a defect may exist in the driving pin used to control the oil pressure of the power steering. Consequence: if a defective driving pin exists in a vehicle and the pin breaks during normal vehicle turning, the normally available hydraulic support function will no longer function and steering wheel operation will be limited. Action: mercedes-benz will replace the steering gears. the recall began on january 28, 2009. owner may contact mercedes-benz at 1-800-367-6372. Recall Date: 12/19/2008 | |
| 2008 MERCEDES M CLASS Manufactured between: 02/01/2005 and 04/30/2008 Defect: mercedes-benz is recalling my 2006-2008 m-class, r-class, my 2005-2009 slk-class, my 2005-2008 c-class, my 2003-2004 and 2006-2008 clk-class, my 2003-2008 e-class, my 2004 and 2008 cl-class, my 2008 cls-class, my 2004 and 2007-2008 s-class, my 2003 g-class, and my 2003-2004, 2006 and 2009 sl-class vehicles. a software calibration number (scn) coding received on the affected vehicles during a recent workshop visit was incorrect. depending on the model year and model affected, the results of an incorrect scn coding can affect a number of vehicle safety and emission functions including the following types of functions: (1) the fuel gauge readings may be incorrect; (2) a stuck fuel-level sensor may not be displayed in the instrument cluster; (3) the obd system may cause the check engine light to illuminate incorrectly; and, (4) the speedometer may be out of tolerance. Consequence: in the event of a vehicle crash, the electrical fuel pump may not receive a crash signal that is required for the fuel pump to disconnect and prevent future fuel delivery as designed. Action: dealers will recode the scn free of charge. the recall began on august 30, 2008. owners may contact mercedes-benz at 1-800-367-6372. Recall Date: 07/07/2008 | |
| 2004 MERCEDES M CLASS Manufactured between: 08/01/1999 and 06/30/2004 Defect: mercedes-benz is recalling certain model year 2000-2002 m-class and model year 2000-2004 m-class amg vehicles. the cruise control system in the affected vehicles allows the driver to disengage the system in a number of ways, including tapping the brake pedal, using the cruise control stalk, or braking the vehicle enough to reach a certain rate of deceleration. mercedes-benz has determined that under certain circumstances use of the brake pedal may not automatically disengage cruise control as expected by the driver, although the other means of deactivating cruise control remain fully operative. specifically, where the driver pumps the brakes rather than applying consistent pedal force, the level of force required may be unusually high. Consequence: difficulty or delay in disengaging cruise control can increase the risk of a crash. Action: dealers will repair the vehicles free of charge. the safety recall is expected to begin during september 2011. owners may contact mercedes-benz at 1-800-367-6372. Recall Date: 03/31/2011 | |
| M-CLASS RECALLS | Top |
| 2009 MERCEDES M-CLASS Manufactured between: 07/01/2008 and 03/09/2009 Defect: mercedes benz is recalling 16,130 my 2009 m-class w164 passenger vehicles equipped with the optional power lift gate. as a result of a faulty seal around the rear tail lamp assembly, water may enter the rear compartment containing the spare tire. water contamination of the control unit for the power lift gate can result in disabling of the power lift gate motor. Consequence: water will cause a short circuit which could lead to a fire. Action: dealers will replace the seal of the rear tail lamp assembly with a thicker one and reposition the affected power lift gate control unit inside the chassis. this service will be performed free of charge. the recall is expected to begin during april 2009. owners may contact mercedes-benz at 1-800-367-6372. Recall Date: 03/10/2009 | |
| 2007 MERCEDES M-CLASS Manufactured between: 02/01/2005 and 04/30/2008 Defect: mercedes-benz is recalling my 2006-2008 m-class, r-class, my 2005-2009 slk-class, my 2005-2008 c-class, my 2003-2004 and 2006-2008 clk-class, my 2003-2008 e-class, my 2004 and 2008 cl-class, my 2008 cls-class, my 2004 and 2007-2008 s-class, my 2003 g-class, and my 2003-2004, 2006 and 2009 sl-class vehicles. a software calibration number (scn) coding received on the affected vehicles during a recent workshop visit was incorrect. depending on the model year and model affected, the results of an incorrect scn coding can affect a number of vehicle safety and emission functions including the following types of functions: (1) the fuel gauge readings may be incorrect; (2) a stuck fuel-level sensor may not be displayed in the instrument cluster; (3) the obd system may cause the check engine light to illuminate incorrectly; and, (4) the speedometer may be out of tolerance. Consequence: in the event of a vehicle crash, the electrical fuel pump may not receive a crash signal that is required for the fuel pump to disconnect and prevent future fuel delivery as designed. Action: dealers will recode the scn free of charge. the recall began on august 30, 2008. owners may contact mercedes-benz at 1-800-367-6372. Recall Date: 07/07/2008 | |
| 2007 MERCEDES M-CLASS Manufactured between: 11/28/2006 and 12/12/2006 Defect: on certain vehicles, the accelerator pedal might not have been fully fastened to its mounting studs. Consequence: over time, the pedal may not maintain a consistent pedal position, which could make it more difficult to operate the accelerator. Action: dealers will inspect and, if necessary, install the mounting nuts of the accelerator pedal. the recall began on january 16, 2007. owners may contact mercedes-benz at 1-800-367-6372. Recall Date: 12/29/2006 | |
| 2006 MERCEDES M-CLASS Manufactured between: 02/01/2005 and 04/30/2008 Defect: mercedes-benz is recalling my 2006-2008 m-class, r-class, my 2005-2009 slk-class, my 2005-2008 c-class, my 2003-2004 and 2006-2008 clk-class, my 2003-2008 e-class, my 2004 and 2008 cl-class, my 2008 cls-class, my 2004 and 2007-2008 s-class, my 2003 g-class, and my 2003-2004, 2006 and 2009 sl-class vehicles. a software calibration number (scn) coding received on the affected vehicles during a recent workshop visit was incorrect. depending on the model year and model affected, the results of an incorrect scn coding can affect a number of vehicle safety and emission functions including the following types of functions: (1) the fuel gauge readings may be incorrect; (2) a stuck fuel-level sensor may not be displayed in the instrument cluster; (3) the obd system may cause the check engine light to illuminate incorrectly; and, (4) the speedometer may be out of tolerance. Consequence: in the event of a vehicle crash, the electrical fuel pump may not receive a crash signal that is required for the fuel pump to disconnect and prevent future fuel delivery as designed. Action: dealers will recode the scn free of charge. the recall began on august 30, 2008. owners may contact mercedes-benz at 1-800-367-6372. Recall Date: 07/07/2008 | |
| ML RECALLS | Top |
| 2008 MERCEDES ML Manufactured between: 07/01/2006 and 04/30/2008 Defect: mercedes-benz is recalling 52,740 my 2006-2008 gl and ml class vehicles equipped with flex-n-gate trailer hitch. some of the weld seams connecting the trailer hitch receiver to the attachment bar used to secure the trailer hitch to the body frame do not meet performance specifications. Consequence: this may result in the traile rhitch receiver separating from the attachment bar, creating a road hazard which may lead to a vehicle crash. the trailer hitch must not be used for any purpose until it has been repaired. Action: dealers will repair the trailer hitch. the recall began on june 16, 2008. owenrs may contact mercedes-benz at 1-800-367-6372. Recall Date: 06/02/2008 | |
| 2008 MERCEDES ML Manufactured between: 05/01/2006 and 10/31/2007 Defect: on certain passenger vehicles equipped with diesel engines, the crankshaft sensor could fail due to separation of bond wires from the lead frame in the sensor. this results in an interruption in the electrical connection in the chip housing of the sensor. Consequence: when this happens, the vehicle may lose power rather than enter a limp-home mode. in addition, the vehicle cannot be restarted after failure of the electrical connection in the sensor, increasing the risk of a crash. Action: dealers will replace the crankshaft sensor. the recall began on february 4, 2008. owners may contact mercedes-benz at 1-800-367-6372. Recall Date: 01/09/2008 | |
| 2007 MERCEDES ML Manufactured between: 07/01/2006 and 04/30/2008 Defect: mercedes-benz is recalling 52,740 my 2006-2008 gl and ml class vehicles equipped with flex-n-gate trailer hitch. some of the weld seams connecting the trailer hitch receiver to the attachment bar used to secure the trailer hitch to the body frame do not meet performance specifications. Consequence: this may result in the traile rhitch receiver separating from the attachment bar, creating a road hazard which may lead to a vehicle crash. the trailer hitch must not be used for any purpose until it has been repaired. Action: dealers will repair the trailer hitch. the recall began on june 16, 2008. owenrs may contact mercedes-benz at 1-800-367-6372. Recall Date: 06/02/2008 | |
| 2007 MERCEDES ML Manufactured between: 05/01/2006 and 10/31/2007 Defect: on certain passenger vehicles equipped with diesel engines, the crankshaft sensor could fail due to separation of bond wires from the lead frame in the sensor. this results in an interruption in the electrical connection in the chip housing of the sensor. Consequence: when this happens, the vehicle may lose power rather than enter a limp-home mode. in addition, the vehicle cannot be restarted after failure of the electrical connection in the sensor, increasing the risk of a crash. Action: dealers will replace the crankshaft sensor. the recall began on february 4, 2008. owners may contact mercedes-benz at 1-800-367-6372. Recall Date: 01/09/2008 | |
| 2006 MERCEDES ML Manufactured between: 07/01/2006 and 04/30/2008 Defect: mercedes-benz is recalling 52,740 my 2006-2008 gl and ml class vehicles equipped with flex-n-gate trailer hitch. some of the weld seams connecting the trailer hitch receiver to the attachment bar used to secure the trailer hitch to the body frame do not meet performance specifications. Consequence: this may result in the traile rhitch receiver separating from the attachment bar, creating a road hazard which may lead to a vehicle crash. the trailer hitch must not be used for any purpose until it has been repaired. Action: dealers will repair the trailer hitch. the recall began on june 16, 2008. owenrs may contact mercedes-benz at 1-800-367-6372. Recall Date: 06/02/2008 | |
| 2006 MERCEDES ML Manufactured between: 05/01/2006 and 10/31/2007 Defect: on certain passenger vehicles equipped with diesel engines, the crankshaft sensor could fail due to separation of bond wires from the lead frame in the sensor. this results in an interruption in the electrical connection in the chip housing of the sensor. Consequence: when this happens, the vehicle may lose power rather than enter a limp-home mode. in addition, the vehicle cannot be restarted after failure of the electrical connection in the sensor, increasing the risk of a crash. Action: dealers will replace the crankshaft sensor. the recall began on february 4, 2008. owners may contact mercedes-benz at 1-800-367-6372. Recall Date: 01/09/2008 | |
| R RECALLS | Top |
| 2011 MERCEDES R Manufactured between: 04/30/2010 and 10/30/2010 Defect: mercedes benz is recalling certain model year 2011 m-class, model w164, gl-class, model x164, e-class, model w212, r-class, and model v251vehicles. the o-ring may not have been properly lubricated in all cases. lack of lubrication can lead to leakage of the fuel filter. Consequence: diesel fuel may be deposited on roads and making those roads slippery, increasing the potential for a crash. Action: dealers will replace the fuel filters free of charge. the safety recall began on november 24, 2010. owners may contact mercedes benz at 1-800-367-6372. Recall Date: 10/29/2010 | |
| 2008 MERCEDES R Manufactured between: 03/03/2008 and 03/20/2008 Defect: mercedes-benz is recalling 577 my 2008 gl-class, m-class, and r-class vehicles. a defect may exist in the driving pin used to control the oil pressure of the power steering. Consequence: if a defective driving pin exists in a vehicle and the pin breaks during normal vehicle turning, the normally available hydraulic support function will no longer function and steering wheel operation will be limited. Action: mercedes-benz will replace the steering gears. the recall began on january 28, 2009. owner may contact mercedes-benz at 1-800-367-6372. Recall Date: 12/19/2008 | |
| 2008 MERCEDES R Manufactured between: 09/01/2005 and 05/31/2008 Defect: mercedes-benz is recalling my 2006-2008 m-class, r-class, my 2005-2009 slk-class, my 2005-2008 c-class, my 2003-2004 and 2006-2008 clk-class, my 2003-2008 e-class, my 2004 and 2008 cl-class, my 2008 cls-class, my 2004 and 2007-2008 s-class, my 2003 g-class, and my 2003-2004, 2006 and 2009 sl-class vehicles. a software calibration number (scn) coding received on the affected vehicles during a recent workshop visit was incorrect. depending on the model year and model affected, the results of an incorrect scn coding can affect a number of vehicle safety and emission functions including the following types of functions: (1) the fuel gauge readings may be incorrect; (2) a stuck fuel-level sensor may not be displayed in the instrument cluster; (3) the obd system may cause the check engine light to illuminate incorrectly; and, (4) the speedometer may be out of tolerance. Consequence: in the event of a vehicle crash, the electrical fuel pump may not receive a crash signal that is required for the fuel pump to disconnect and prevent future fuel delivery as designed. Action: dealers will recode the scn free of charge. the recall began on august 30, 2008. owners may contact mercedes-benz at 1-800-367-6372. Recall Date: 07/07/2008 | |
| 2008 MERCEDES R Manufactured between: 05/01/2006 and 10/31/2007 Defect: on certain passenger vehicles equipped with diesel engines, the crankshaft sensor could fail due to separation of bond wires from the lead frame in the sensor. this results in an interruption in the electrical connection in the chip housing of the sensor. Consequence: when this happens, the vehicle may lose power rather than enter a limp-home mode. in addition, the vehicle cannot be restarted after failure of the electrical connection in the sensor, increasing the risk of a crash. Action: dealers will replace the crankshaft sensor. the recall began on february 4, 2008. owners may contact mercedes-benz at 1-800-367-6372. Recall Date: 01/09/2008 | |
| R CLASS RECALLS | Top |
| 2006 MERCEDES R CLASS Manufactured between: 09/01/2005 and 05/31/2008 Defect: mercedes-benz is recalling my 2006-2008 m-class, r-class, my 2005-2009 slk-class, my 2005-2008 c-class, my 2003-2004 and 2006-2008 clk-class, my 2003-2008 e-class, my 2004 and 2008 cl-class, my 2008 cls-class, my 2004 and 2007-2008 s-class, my 2003 g-class, and my 2003-2004, 2006 and 2009 sl-class vehicles. a software calibration number (scn) coding received on the affected vehicles during a recent workshop visit was incorrect. depending on the model year and model affected, the results of an incorrect scn coding can affect a number of vehicle safety and emission functions including the following types of functions: (1) the fuel gauge readings may be incorrect; (2) a stuck fuel-level sensor may not be displayed in the instrument cluster; (3) the obd system may cause the check engine light to illuminate incorrectly; and, (4) the speedometer may be out of tolerance. Consequence: in the event of a vehicle crash, the electrical fuel pump may not receive a crash signal that is required for the fuel pump to disconnect and prevent future fuel delivery as designed. Action: dealers will recode the scn free of charge. the recall began on august 30, 2008. owners may contact mercedes-benz at 1-800-367-6372. Recall Date: 07/07/2008 | |
| 2006 MERCEDES R CLASS Manufactured between: 05/01/2006 and 10/31/2007 Defect: on certain passenger vehicles equipped with diesel engines, the crankshaft sensor could fail due to separation of bond wires from the lead frame in the sensor. this results in an interruption in the electrical connection in the chip housing of the sensor. Consequence: when this happens, the vehicle may lose power rather than enter a limp-home mode. in addition, the vehicle cannot be restarted after failure of the electrical connection in the sensor, increasing the risk of a crash. Action: dealers will replace the crankshaft sensor. the recall began on february 4, 2008. owners may contact mercedes-benz at 1-800-367-6372. Recall Date: 01/09/2008 | |
| 2006 MERCEDES R CLASS Manufactured between: 08/01/2005 and 02/28/2006 Defect: on certain passenger vehicles, the starter wiring harness may be routed incorrectly. this routing could lead to chafing of the protective sleeve covering the starter wiring harness at the engine mount cover. Consequence: over time, such chafing has the potential to wear through the protective sleeve and may expose the underlying starter wiring harness to further chafing, which could result in an electrical short, and the loss of function of the vehicle's electrical system. Action: dealers will inspect and where necessary, correct, the routing of the wiring harness. in the case of wear, the protective sleeve, and if necessary, the starter wiring harness, will be replaced. the recall began on may 12, 2006. owners may contact mercedes-benz at 1-800-367-6372. Recall Date: 04/03/2006 | |
| 2006 MERCEDES R CLASS Manufactured between: 01/01/2006 and 03/31/2006 Defect: on certain passenger vehicles, during the production process, the threads in the nut used to secure the seat belt buckle in a limited number of second row seats may be missing. the absence of the screw threads results in an incomplete connection of the buckle to the seat. Consequence: in the event of a crash, a seat occupant may not be properly restrained increasing the risk of personal injury. Action: dealers will inspect to see if the nut is missing and replace the seat if necessary free of charge. the recall began on may 3, 2006. owners may contact mercedes-benz at 1-800-367-6372. Recall Date: 04/03/2006 | |
| R-CLASS RECALLS | Top |
| 2007 MERCEDES R-CLASS Manufactured between: 09/01/2005 and 05/31/2008 Defect: mercedes-benz is recalling my 2006-2008 m-class, r-class, my 2005-2009 slk-class, my 2005-2008 c-class, my 2003-2004 and 2006-2008 clk-class, my 2003-2008 e-class, my 2004 and 2008 cl-class, my 2008 cls-class, my 2004 and 2007-2008 s-class, my 2003 g-class, and my 2003-2004, 2006 and 2009 sl-class vehicles. a software calibration number (scn) coding received on the affected vehicles during a recent workshop visit was incorrect. depending on the model year and model affected, the results of an incorrect scn coding can affect a number of vehicle safety and emission functions including the following types of functions: (1) the fuel gauge readings may be incorrect; (2) a stuck fuel-level sensor may not be displayed in the instrument cluster; (3) the obd system may cause the check engine light to illuminate incorrectly; and, (4) the speedometer may be out of tolerance. Consequence: in the event of a vehicle crash, the electrical fuel pump may not receive a crash signal that is required for the fuel pump to disconnect and prevent future fuel delivery as designed. Action: dealers will recode the scn free of charge. the recall began on august 30, 2008. owners may contact mercedes-benz at 1-800-367-6372. Recall Date: 07/07/2008 | |
| 2007 MERCEDES R-CLASS Manufactured between: 05/01/2006 and 10/31/2007 Defect: on certain passenger vehicles equipped with diesel engines, the crankshaft sensor could fail due to separation of bond wires from the lead frame in the sensor. this results in an interruption in the electrical connection in the chip housing of the sensor. Consequence: when this happens, the vehicle may lose power rather than enter a limp-home mode. in addition, the vehicle cannot be restarted after failure of the electrical connection in the sensor, increasing the risk of a crash. Action: dealers will replace the crankshaft sensor. the recall began on february 4, 2008. owners may contact mercedes-benz at 1-800-367-6372. Recall Date: 01/09/2008 | |
| 2007 MERCEDES R-CLASS Manufactured between: 11/28/2006 and 12/12/2006 Defect: on certain vehicles, the accelerator pedal might not have been fully fastened to its mounting studs. Consequence: over time, the pedal may not maintain a consistent pedal position, which could make it more difficult to operate the accelerator. Action: dealers will inspect and, if necessary, install the mounting nuts of the accelerator pedal. the recall began on january 16, 2007. owners may contact mercedes-benz at 1-800-367-6372. Recall Date: 12/29/2006 | |
| S RECALLS | Top |
| 2008 MERCEDES S Manufactured between: 12/01/2005 and 03/31/2008 Defect: mercedes-benz is recalling my 2006-2008 m-class, r-class, my 2005-2009 slk-class, my 2005-2008 c-class, my 2003-2004 and 2006-2008 clk-class, my 2003-2008 e-class, my 2004 and 2008 cl-class, my 2008 cls-class, my 2004 and 2007-2008 s-class, my 2003 g-class, and my 2003-2004, 2006 and 2009 sl-class vehicles. a software calibration number (scn) coding received on the affected vehicles during a recent workshop visit was incorrect. depending on the model year and model affected, the results of an incorrect scn coding can affect a number of vehicle safety and emission functions including the following types of functions: (1) the fuel gauge readings may be incorrect; (2) a stuck fuel-level sensor may not be displayed in the instrument cluster; (3) the obd system may cause the check engine light to illuminate incorrectly; and, (4) the speedometer may be out of tolerance. Consequence: in the event of a vehicle crash, the electrical fuel pump may not receive a crash signal that is required for the fuel pump to disconnect and prevent future fuel delivery as designed. Action: dealers will recode the scn free of charge. the recall began on august 30, 2008. owners may contact mercedes-benz at 1-800-367-6372. Recall Date: 07/07/2008 | |
| 2008 MERCEDES S Manufactured between: 10/27/2007 and 11/30/2007 Defect: mercedes-benz is recalling 3,283 my 2008 s-class and cl-class passenger vehicles. a malfunction may occur on the signal acquisition and actuation module-front (sam-f) transistors. the sam-f is a double transistor that helps control vehicle functions and the lighting of the center console. incorrect storage of the transistors led the transistors to be exposed to excess humidity. Consequence: the presence of this moisture in combination with the thermal stress during the "reflow soldering" may damage the transistors and prevent them from properly functioning which will increase the risk of crash. Action: dealers will inspect and replace all potentially affected sam free of charge. the recall began on may 2, 2008. owner may contact mercedes benz at 1-800-367-6372. Recall Date: 03/19/2008 | |
| 2008 MERCEDES S Manufactured between: 10/27/2007 and 11/30/2007 Defect: mercedes-benz is recalling 3,283 my 2008 s-class and cl-class passenger vehicles. a malfunction may occur on the signal acquisition and actuation module-front (sam-f) transistors. the sam-f is a double transistor that helps control vehicle functions and the lighting of the center console. incorrect storage of the transistors led the transistors to be exposed to excess humidity. Consequence: the presence of this moisture in combination with the thermal stress during the "reflow soldering" may damage the transistors and prevent them from properly functioning which will increase the risk of crash. Action: dealers will inspect and replace all potentially affected sam free of charge. the recall began on may 2, 2008. owner may contact mercedes benz at 1-800-367-6372. Recall Date: 03/19/2008 | |
| 2007 MERCEDES S Manufactured between: 05/17/2005 and 09/05/2006 Defect: mercedes-benz is recalling 1,515 my 2007 s-class vehicles. the radial knuckle of the front strut may fail. the radial knuckle flaw may occur after significant mileage accumulation combined with exposure to high continuous stress by driving on rough roads. Consequence: if a radial knuckle fails, the steering control of the vehicle may be affected, increasing the risk of a crash. Action: dealers will check and replace, if necessary, the ball joint(s). the recall is expected to begin during february 2009. owners may contact mercedes-benz at 1-800-367-6372. Recall Date: 11/24/2008 | |
| 2007 MERCEDES S Manufactured between: 12/01/2005 and 03/31/2008 Defect: mercedes-benz is recalling my 2006-2008 m-class, r-class, my 2005-2009 slk-class, my 2005-2008 c-class, my 2003-2004 and 2006-2008 clk-class, my 2003-2008 e-class, my 2004 and 2008 cl-class, my 2008 cls-class, my 2004 and 2007-2008 s-class, my 2003 g-class, and my 2003-2004, 2006 and 2009 sl-class vehicles. a software calibration number (scn) coding received on the affected vehicles during a recent workshop visit was incorrect. depending on the model year and model affected, the results of an incorrect scn coding can affect a number of vehicle safety and emission functions including the following types of functions: (1) the fuel gauge readings may be incorrect; (2) a stuck fuel-level sensor may not be displayed in the instrument cluster; (3) the obd system may cause the check engine light to illuminate incorrectly; and, (4) the speedometer may be out of tolerance. Consequence: in the event of a vehicle crash, the electrical fuel pump may not receive a crash signal that is required for the fuel pump to disconnect and prevent future fuel delivery as designed. Action: dealers will recode the scn free of charge. the recall began on august 30, 2008. owners may contact mercedes-benz at 1-800-367-6372. Recall Date: 07/07/2008 | |
| S CLASS RECALLS | Top |
| 2009 MERCEDES S CLASS Manufactured between: 09/01/2008 and 09/30/2008 Defect: mercedes benz is recalling 54 my 2009 s-class, w221 vehicles. during production the front and rear passenger side door locks may have been mistakenly interchanged during production. the exchange of a front and a rear passenger side door lock would result in a passenger side door that cannot be opened by merely pulling on the interior handle and a rear door lock that can be opened with a simple pull of the interior door handle even if locked. Consequence: this situation could affect the safe exiting of a vehicle in the event of a crash or protection of children from inadvertent opening of the rear door. Action: dealers will check the part number on all door locks and replace any incorrectly installed door lock free of charge. the recall began on march 27, 2009. owners may contact mercedes benz at 1-800-367-6372. Recall Date: 03/13/2009 | |
| 2005 MERCEDES S CLASS Manufactured between: 05/01/2004 and 09/30/2004 Defect: on certain vehicles, the instrument cluster is experiencing electrical malfunctions. the instrument cluster contains gauges and indicators that must be illuminated whenever the vehicle is in operation. Consequence: due to inadequate illumination, the driver will be unable to read the gauges and indicators, such as the speedometer, which could increase the risk of a crash. Action: dealers will replace the instrument cluster modules. the recall will be conducted in phases. phase i was mailed out to approximately 7,500 owners on september 29, 2006. phase ii and phase iii is scheduled for december 2006. owners may contact mercedes-benz at 1-800-367-6372. Recall Date: 02/02/2006 | |
| 2004 MERCEDES S CLASS Manufactured between: 05/01/2004 and 05/31/2004 Defect: mercedes-benz is recalling my 2006-2008 m-class, r-class, my 2005-2009 slk-class, my 2005-2008 c-class, my 2003-2004 and 2006-2008 clk-class, my 2003-2008 e-class, my 2004 and 2008 cl-class, my 2008 cls-class, my 2004 and 2007-2008 s-class, my 2003 g-class, and my 2003-2004, 2006 and 2009 sl-class vehicles. a software calibration number (scn) coding received on the affected vehicles during a recent workshop visit was incorrect. depending on the model year and model affected, the results of an incorrect scn coding can affect a number of vehicle safety and emission functions including the following types of functions: (1) the fuel gauge readings may be incorrect; (2) a stuck fuel-level sensor may not be displayed in the instrument cluster; (3) the obd system may cause the check engine light to illuminate incorrectly; and, (4) the speedometer may be out of tolerance. Consequence: in the event of a vehicle crash, the electrical fuel pump may not receive a crash signal that is required for the fuel pump to disconnect and prevent future fuel delivery as designed. Action: dealers will recode the scn free of charge. the recall began on august 30, 2008. owners may contact mercedes-benz at 1-800-367-6372. Recall Date: 07/07/2008 | |
| 2004 MERCEDES S CLASS Manufactured between: 05/01/2004 and 09/30/2004 Defect: on certain vehicles, the instrument cluster is experiencing electrical malfunctions. the instrument cluster contains gauges and indicators that must be illuminated whenever the vehicle is in operation. Consequence: due to inadequate illumination, the driver will be unable to read the gauges and indicators, such as the speedometer, which could increase the risk of a crash. Action: dealers will replace the instrument cluster modules. the recall will be conducted in phases. phase i was mailed out to approximately 7,500 owners on september 29, 2006. phase ii and phase iii is scheduled for december 2006. owners may contact mercedes-benz at 1-800-367-6372. Recall Date: 02/02/2006 | |
| 2004 MERCEDES S CLASS Manufactured between: 11/01/2002 and 10/31/2003 Defect: on certain vehicles, the trunk lid springs could fail in the closed trunk lid position. Consequence: if the trunk lid is manually lifted, it may not remain in the up position and could cause injury if it comes down while someone is reaching into the trunk. Action: dealers will replace both trunk lid springs. the recall began august 17, 2004. owners should contact mercedes- benz at 1-800-367-6372. Recall Date: 06/09/2004 | |
| S-600 RECALLS | Top |
| 2004 MERCEDES S-600 Manufactured between: 04/01/2000 and 03/31/2004 Defect: on certain passenger vehicles, corrosion may occur in the inner steel portions of the active body control's (abc) high-pressure distribution hose due to extensive exposure to heat and humidity. over time, corrosion may deteriorate the inner steel portions of the hose. Consequence: this may result in abc hydraulic fluid leakage. under some circumstances, leaking hydraulic fluid may come in contact with hot engine components and lead to a possibility of fire. Action: dealers will install new, corrosion resistant abc high-pressure distribution hoses. the recall began august 31, 2004. owners should contact mercedes-benz at 1-800-367-6372. Recall Date: 05/13/2004 | |
| S220 RECALLS | Top |
| 2006 MERCEDES S220 Manufactured between: 04/01/2002 and 02/28/2005 Defect: mercedes benz is recalling 4,564 my 2001-2006 cl-class (model 215), my 2002-2006 s-class (model 220), my 2003-2007 sl-class (model 230), my 2007-2008 cl-class (model 216), and my 2007 s-class (model 221)passenger vehicles equipped with active body control (abc) acceleration sensors on the front struts. these sensors measure acceleration around the z-axis of the vehicle and assure an automatic adaptation of the front struts to maintain a relatively level body position. variations in the soldering process resulted in soldering points on the board of the abc sensors which may not be within design tolerances. signals from the affected sensors measuring the acceleration may not be accurately transmitted to the engine control unit. Consequence: a variation in the transmitted values between affected and unaffected sensors can result in one front strut adjusting to a value indicating body movement while another strut does not adjust presenting the driver with an uneven front suspension. this condition may lead to unexpected body movements at the front axle which can adversely influence the vehicle's directional stability and could lead to a vehicle crash. Action: dealers will inspect and replace, if necessary, the front abc sensors in all potentially affected vehicles. the recall began on september 22, 2008. owners may contact mercedes-benz at 1-800-367-6372. Recall Date: 08/14/2008 | |
| 2005 MERCEDES S220 Manufactured between: 04/01/2002 and 02/28/2005 Defect: mercedes benz is recalling 4,564 my 2001-2006 cl-class (model 215), my 2002-2006 s-class (model 220), my 2003-2007 sl-class (model 230), my 2007-2008 cl-class (model 216), and my 2007 s-class (model 221)passenger vehicles equipped with active body control (abc) acceleration sensors on the front struts. these sensors measure acceleration around the z-axis of the vehicle and assure an automatic adaptation of the front struts to maintain a relatively level body position. variations in the soldering process resulted in soldering points on the board of the abc sensors which may not be within design tolerances. signals from the affected sensors measuring the acceleration may not be accurately transmitted to the engine control unit. Consequence: a variation in the transmitted values between affected and unaffected sensors can result in one front strut adjusting to a value indicating body movement while another strut does not adjust presenting the driver with an uneven front suspension. this condition may lead to unexpected body movements at the front axle which can adversely influence the vehicle's directional stability and could lead to a vehicle crash. Action: dealers will inspect and replace, if necessary, the front abc sensors in all potentially affected vehicles. the recall began on september 22, 2008. owners may contact mercedes-benz at 1-800-367-6372. Recall Date: 08/14/2008 | |
| 2004 MERCEDES S220 Manufactured between: 04/01/2002 and 02/28/2005 Defect: mercedes benz is recalling 4,564 my 2001-2006 cl-class (model 215), my 2002-2006 s-class (model 220), my 2003-2007 sl-class (model 230), my 2007-2008 cl-class (model 216), and my 2007 s-class (model 221)passenger vehicles equipped with active body control (abc) acceleration sensors on the front struts. these sensors measure acceleration around the z-axis of the vehicle and assure an automatic adaptation of the front struts to maintain a relatively level body position. variations in the soldering process resulted in soldering points on the board of the abc sensors which may not be within design tolerances. signals from the affected sensors measuring the acceleration may not be accurately transmitted to the engine control unit. Consequence: a variation in the transmitted values between affected and unaffected sensors can result in one front strut adjusting to a value indicating body movement while another strut does not adjust presenting the driver with an uneven front suspension. this condition may lead to unexpected body movements at the front axle which can adversely influence the vehicle's directional stability and could lead to a vehicle crash. Action: dealers will inspect and replace, if necessary, the front abc sensors in all potentially affected vehicles. the recall began on september 22, 2008. owners may contact mercedes-benz at 1-800-367-6372. Recall Date: 08/14/2008 | |
| S221 RECALLS | Top |
| 2007 MERCEDES S221 Manufactured between: 01/01/2006 and 12/31/2006 Defect: mercedes benz is recalling 4,564 my 2001-2006 cl-class (model 215), my 2002-2006 s-class (model 220), my 2003-2007 sl-class (model 230), my 2007-2008 cl-class (model 216), and my 2007 s-class (model 221)passenger vehicles equipped with active body control (abc) acceleration sensors on the front struts. these sensors measure acceleration around the z-axis of the vehicle and assure an automatic adaptation of the front struts to maintain a relatively level body position. variations in the soldering process resulted in soldering points on the board of the abc sensors which may not be within design tolerances. signals from the affected sensors measuring the acceleration may not be accurately transmitted to the engine control unit. Consequence: a variation in the transmitted values between affected and unaffected sensors can result in one front strut adjusting to a value indicating body movement while another strut does not adjust presenting the driver with an uneven front suspension. this condition may lead to unexpected body movements at the front axle which can adversely influence the vehicle's directional stability and could lead to a vehicle crash. Action: dealers will inspect and replace, if necessary, the front abc sensors in all potentially affected vehicles. the recall began on september 22, 2008. owners may contact mercedes-benz at 1-800-367-6372. Recall Date: 08/14/2008 | |
| SL CLASS RECALLS | Top |
| 2009 MERCEDES SL CLASS Manufactured between: 03/01/2003 and 02/28/2008 Defect: mercedes-benz is recalling my 2006-2008 m-class, r-class, my 2005-2009 slk-class, my 2005-2008 c-class, my 2003-2004 and 2006-2008 clk-class, my 2003-2008 e-class, my 2004 and 2008 cl-class, my 2008 cls-class, my 2004 and 2007-2008 s-class, my 2003 g-class, and my 2003-2004, 2006 and 2009 sl-class vehicles. a software calibration number (scn) coding received on the affected vehicles during a recent workshop visit was incorrect. depending on the model year and model affected, the results of an incorrect scn coding can affect a number of vehicle safety and emission functions including the following types of functions: (1) the fuel gauge readings may be incorrect; (2) a stuck fuel-level sensor may not be displayed in the instrument cluster; (3) the obd system may cause the check engine light to illuminate incorrectly; and, (4) the speedometer may be out of tolerance. Consequence: in the event of a vehicle crash, the electrical fuel pump may not receive a crash signal that is required for the fuel pump to disconnect and prevent future fuel delivery as designed. Action: dealers will recode the scn free of charge. the recall began on august 30, 2008. owners may contact mercedes-benz at 1-800-367-6372. Recall Date: 07/07/2008 | |
| 2006 MERCEDES SL CLASS Manufactured between: 03/01/2003 and 02/28/2008 Defect: mercedes-benz is recalling my 2006-2008 m-class, r-class, my 2005-2009 slk-class, my 2005-2008 c-class, my 2003-2004 and 2006-2008 clk-class, my 2003-2008 e-class, my 2004 and 2008 cl-class, my 2008 cls-class, my 2004 and 2007-2008 s-class, my 2003 g-class, and my 2003-2004, 2006 and 2009 sl-class vehicles. a software calibration number (scn) coding received on the affected vehicles during a recent workshop visit was incorrect. depending on the model year and model affected, the results of an incorrect scn coding can affect a number of vehicle safety and emission functions including the following types of functions: (1) the fuel gauge readings may be incorrect; (2) a stuck fuel-level sensor may not be displayed in the instrument cluster; (3) the obd system may cause the check engine light to illuminate incorrectly; and, (4) the speedometer may be out of tolerance. Consequence: in the event of a vehicle crash, the electrical fuel pump may not receive a crash signal that is required for the fuel pump to disconnect and prevent future fuel delivery as designed. Action: dealers will recode the scn free of charge. the recall began on august 30, 2008. owners may contact mercedes-benz at 1-800-367-6372. Recall Date: 07/07/2008 | |
| 2005 MERCEDES SL CLASS Manufactured between: 06/01/2001 and 03/31/2005 Defect: on certain vehicles, the sensotronic brake control (sbc) system may prematurely shift to the hydraulic back-up function mode, due to deterioration of the wiring harness connection, or due to premature failure of the hydraulic pump. Consequence: in the hydraulic back-up mode, the driver has braking power sufficient to stop the vehicle, although greater brake pedal pressure is required and the brake pedal travel will be noticeably longer. Action: dealers will install a bracket and replacement ground wire to the sbc pump unit on all vehicles free of charge. additionally dealers will inspect and replace the sbc pump unit in sl vehicles produced during a limited production period. the recall began on august 8, 2005. owners may contact mercedes-benz at 1-800-367-6372. Recall Date: 04/01/2005 | |
| 2004 MERCEDES SL CLASS Manufactured between: 03/01/2003 and 02/28/2008 Defect: mercedes-benz is recalling my 2006-2008 m-class, r-class, my 2005-2009 slk-class, my 2005-2008 c-class, my 2003-2004 and 2006-2008 clk-class, my 2003-2008 e-class, my 2004 and 2008 cl-class, my 2008 cls-class, my 2004 and 2007-2008 s-class, my 2003 g-class, and my 2003-2004, 2006 and 2009 sl-class vehicles. a software calibration number (scn) coding received on the affected vehicles during a recent workshop visit was incorrect. depending on the model year and model affected, the results of an incorrect scn coding can affect a number of vehicle safety and emission functions including the following types of functions: (1) the fuel gauge readings may be incorrect; (2) a stuck fuel-level sensor may not be displayed in the instrument cluster; (3) the obd system may cause the check engine light to illuminate incorrectly; and, (4) the speedometer may be out of tolerance. Consequence: in the event of a vehicle crash, the electrical fuel pump may not receive a crash signal that is required for the fuel pump to disconnect and prevent future fuel delivery as designed. Action: dealers will recode the scn free of charge. the recall began on august 30, 2008. owners may contact mercedes-benz at 1-800-367-6372. Recall Date: 07/07/2008 | |
| 2004 MERCEDES SL CLASS Manufactured between: 06/01/2001 and 03/31/2005 Defect: on certain vehicles, the sensotronic brake control (sbc) system may prematurely shift to the hydraulic back-up function mode, due to deterioration of the wiring harness connection, or due to premature failure of the hydraulic pump. Consequence: in the hydraulic back-up mode, the driver has braking power sufficient to stop the vehicle, although greater brake pedal pressure is required and the brake pedal travel will be noticeably longer. Action: dealers will install a bracket and replacement ground wire to the sbc pump unit on all vehicles free of charge. additionally dealers will inspect and replace the sbc pump unit in sl vehicles produced during a limited production period. the recall began on august 8, 2005. owners may contact mercedes-benz at 1-800-367-6372. Recall Date: 04/01/2005 | |
| 2004 MERCEDES SL CLASS Manufactured between: 10/01/2001 and 05/31/2004 Defect: on certain vehicles, the electronic monitoring system of the sensotronic brake control (sbc) is designed to monitor the pressure gradient within the high pressure line of the brake system. if an unacceptable pressure gradient is detected, the system will switch, as it is designed to do, into the hydraulic function mode. Consequence: if vehicles are not routinely serviced and have extremely high mileage combined with a high number of brake actuations, or a high brake actuation frequency, the pump motor of the sbc may run out of permissible tolerances, thereby triggering the hydraulic function mode. Action: dealers will inspect the sbc hydraulic unit, replacing it if necessary. the recall began on october 21m 2004. owners should contact mercedes-benz at 1-800-367-6372. Recall Date: 06/22/2004 | |
| SL230 RECALLS | Top |
| 2007 MERCEDES SL230 Manufactured between: 05/01/2002 and 12/31/2006 Defect: mercedes benz is recalling 4,564 my 2001-2006 cl-class (model 215), my 2002-2006 s-class (model 220), my 2003-2007 sl-class (model 230), my 2007-2008 cl-class (model 216), and my 2007 s-class (model 221)passenger vehicles equipped with active body control (abc) acceleration sensors on the front struts. these sensors measure acceleration around the z-axis of the vehicle and assure an automatic adaptation of the front struts to maintain a relatively level body position. variations in the soldering process resulted in soldering points on the board of the abc sensors which may not be within design tolerances. signals from the affected sensors measuring the acceleration may not be accurately transmitted to the engine control unit. Consequence: a variation in the transmitted values between affected and unaffected sensors can result in one front strut adjusting to a value indicating body movement while another strut does not adjust presenting the driver with an uneven front suspension. this condition may lead to unexpected body movements at the front axle which can adversely influence the vehicle's directional stability and could lead to a vehicle crash. Action: dealers will inspect and replace, if necessary, the front abc sensors in all potentially affected vehicles. the recall began on september 22, 2008. owners may contact mercedes-benz at 1-800-367-6372. Recall Date: 08/14/2008 | |
| 2006 MERCEDES SL230 Manufactured between: 05/01/2002 and 12/31/2006 Defect: mercedes benz is recalling 4,564 my 2001-2006 cl-class (model 215), my 2002-2006 s-class (model 220), my 2003-2007 sl-class (model 230), my 2007-2008 cl-class (model 216), and my 2007 s-class (model 221)passenger vehicles equipped with active body control (abc) acceleration sensors on the front struts. these sensors measure acceleration around the z-axis of the vehicle and assure an automatic adaptation of the front struts to maintain a relatively level body position. variations in the soldering process resulted in soldering points on the board of the abc sensors which may not be within design tolerances. signals from the affected sensors measuring the acceleration may not be accurately transmitted to the engine control unit. Consequence: a variation in the transmitted values between affected and unaffected sensors can result in one front strut adjusting to a value indicating body movement while another strut does not adjust presenting the driver with an uneven front suspension. this condition may lead to unexpected body movements at the front axle which can adversely influence the vehicle's directional stability and could lead to a vehicle crash. Action: dealers will inspect and replace, if necessary, the front abc sensors in all potentially affected vehicles. the recall began on september 22, 2008. owners may contact mercedes-benz at 1-800-367-6372. Recall Date: 08/14/2008 | |
| 2005 MERCEDES SL230 Manufactured between: 05/01/2002 and 12/31/2006 Defect: mercedes benz is recalling 4,564 my 2001-2006 cl-class (model 215), my 2002-2006 s-class (model 220), my 2003-2007 sl-class (model 230), my 2007-2008 cl-class (model 216), and my 2007 s-class (model 221)passenger vehicles equipped with active body control (abc) acceleration sensors on the front struts. these sensors measure acceleration around the z-axis of the vehicle and assure an automatic adaptation of the front struts to maintain a relatively level body position. variations in the soldering process resulted in soldering points on the board of the abc sensors which may not be within design tolerances. signals from the affected sensors measuring the acceleration may not be accurately transmitted to the engine control unit. Consequence: a variation in the transmitted values between affected and unaffected sensors can result in one front strut adjusting to a value indicating body movement while another strut does not adjust presenting the driver with an uneven front suspension. this condition may lead to unexpected body movements at the front axle which can adversely influence the vehicle's directional stability and could lead to a vehicle crash. Action: dealers will inspect and replace, if necessary, the front abc sensors in all potentially affected vehicles. the recall began on september 22, 2008. owners may contact mercedes-benz at 1-800-367-6372. Recall Date: 08/14/2008 | |
| 2004 MERCEDES SL230 Manufactured between: 05/01/2002 and 12/31/2006 Defect: mercedes benz is recalling 4,564 my 2001-2006 cl-class (model 215), my 2002-2006 s-class (model 220), my 2003-2007 sl-class (model 230), my 2007-2008 cl-class (model 216), and my 2007 s-class (model 221)passenger vehicles equipped with active body control (abc) acceleration sensors on the front struts. these sensors measure acceleration around the z-axis of the vehicle and assure an automatic adaptation of the front struts to maintain a relatively level body position. variations in the soldering process resulted in soldering points on the board of the abc sensors which may not be within design tolerances. signals from the affected sensors measuring the acceleration may not be accurately transmitted to the engine control unit. Consequence: a variation in the transmitted values between affected and unaffected sensors can result in one front strut adjusting to a value indicating body movement while another strut does not adjust presenting the driver with an uneven front suspension. this condition may lead to unexpected body movements at the front axle which can adversely influence the vehicle's directional stability and could lead to a vehicle crash. Action: dealers will inspect and replace, if necessary, the front abc sensors in all potentially affected vehicles. the recall began on september 22, 2008. owners may contact mercedes-benz at 1-800-367-6372. Recall Date: 08/14/2008 | |
| SLK RECALLS | Top |
| 2009 MERCEDES SLK Manufactured between: 07/01/2004 and 03/31/2008 Defect: mercedes-benz is recalling my 2006-2008 m-class, r-class, my 2005-2009 slk-class, my 2005-2008 c-class, my 2003-2004 and 2006-2008 clk-class, my 2003-2008 e-class, my 2004 and 2008 cl-class, my 2008 cls-class, my 2004 and 2007-2008 s-class, my 2003 g-class, and my 2003-2004, 2006 and 2009 sl-class vehicles. a software calibration number (scn) coding received on the affected vehicles during a recent workshop visit was incorrect. depending on the model year and model affected, the results of an incorrect scn coding can affect a number of vehicle safety and emission functions including the following types of functions: (1) the fuel gauge readings may be incorrect; (2) a stuck fuel-level sensor may not be displayed in the instrument cluster; (3) the obd system may cause the check engine light to illuminate incorrectly; and, (4) the speedometer may be out of tolerance. Consequence: in the event of a vehicle crash, the electrical fuel pump may not receive a crash signal that is required for the fuel pump to disconnect and prevent future fuel delivery as designed. Action: dealers will recode the scn free of charge. the recall began on august 30, 2008. owners may contact mercedes-benz at 1-800-367-6372. Recall Date: 07/07/2008 | |
| 2008 MERCEDES SLK Manufactured between: 07/01/2004 and 03/31/2008 Defect: mercedes-benz is recalling my 2006-2008 m-class, r-class, my 2005-2009 slk-class, my 2005-2008 c-class, my 2003-2004 and 2006-2008 clk-class, my 2003-2008 e-class, my 2004 and 2008 cl-class, my 2008 cls-class, my 2004 and 2007-2008 s-class, my 2003 g-class, and my 2003-2004, 2006 and 2009 sl-class vehicles. a software calibration number (scn) coding received on the affected vehicles during a recent workshop visit was incorrect. depending on the model year and model affected, the results of an incorrect scn coding can affect a number of vehicle safety and emission functions including the following types of functions: (1) the fuel gauge readings may be incorrect; (2) a stuck fuel-level sensor may not be displayed in the instrument cluster; (3) the obd system may cause the check engine light to illuminate incorrectly; and, (4) the speedometer may be out of tolerance. Consequence: in the event of a vehicle crash, the electrical fuel pump may not receive a crash signal that is required for the fuel pump to disconnect and prevent future fuel delivery as designed. Action: dealers will recode the scn free of charge. the recall began on august 30, 2008. owners may contact mercedes-benz at 1-800-367-6372. Recall Date: 07/07/2008 | |
| 2007 MERCEDES SLK Manufactured between: 07/01/2004 and 03/31/2008 Defect: mercedes-benz is recalling my 2006-2008 m-class, r-class, my 2005-2009 slk-class, my 2005-2008 c-class, my 2003-2004 and 2006-2008 clk-class, my 2003-2008 e-class, my 2004 and 2008 cl-class, my 2008 cls-class, my 2004 and 2007-2008 s-class, my 2003 g-class, and my 2003-2004, 2006 and 2009 sl-class vehicles. a software calibration number (scn) coding received on the affected vehicles during a recent workshop visit was incorrect. depending on the model year and model affected, the results of an incorrect scn coding can affect a number of vehicle safety and emission functions including the following types of functions: (1) the fuel gauge readings may be incorrect; (2) a stuck fuel-level sensor may not be displayed in the instrument cluster; (3) the obd system may cause the check engine light to illuminate incorrectly; and, (4) the speedometer may be out of tolerance. Consequence: in the event of a vehicle crash, the electrical fuel pump may not receive a crash signal that is required for the fuel pump to disconnect and prevent future fuel delivery as designed. Action: dealers will recode the scn free of charge. the recall began on august 30, 2008. owners may contact mercedes-benz at 1-800-367-6372. Recall Date: 07/07/2008 | |
| 2006 MERCEDES SLK Manufactured between: 07/01/2004 and 03/31/2008 Defect: mercedes-benz is recalling my 2006-2008 m-class, r-class, my 2005-2009 slk-class, my 2005-2008 c-class, my 2003-2004 and 2006-2008 clk-class, my 2003-2008 e-class, my 2004 and 2008 cl-class, my 2008 cls-class, my 2004 and 2007-2008 s-class, my 2003 g-class, and my 2003-2004, 2006 and 2009 sl-class vehicles. a software calibration number (scn) coding received on the affected vehicles during a recent workshop visit was incorrect. depending on the model year and model affected, the results of an incorrect scn coding can affect a number of vehicle safety and emission functions including the following types of functions: (1) the fuel gauge readings may be incorrect; (2) a stuck fuel-level sensor may not be displayed in the instrument cluster; (3) the obd system may cause the check engine light to illuminate incorrectly; and, (4) the speedometer may be out of tolerance. Consequence: in the event of a vehicle crash, the electrical fuel pump may not receive a crash signal that is required for the fuel pump to disconnect and prevent future fuel delivery as designed. Action: dealers will recode the scn free of charge. the recall began on august 30, 2008. owners may contact mercedes-benz at 1-800-367-6372. Recall Date: 07/07/2008 | |
| 2005 MERCEDES SLK Manufactured between: 07/01/2004 and 03/31/2008 Defect: mercedes-benz is recalling my 2006-2008 m-class, r-class, my 2005-2009 slk-class, my 2005-2008 c-class, my 2003-2004 and 2006-2008 clk-class, my 2003-2008 e-class, my 2004 and 2008 cl-class, my 2008 cls-class, my 2004 and 2007-2008 s-class, my 2003 g-class, and my 2003-2004, 2006 and 2009 sl-class vehicles. a software calibration number (scn) coding received on the affected vehicles during a recent workshop visit was incorrect. depending on the model year and model affected, the results of an incorrect scn coding can affect a number of vehicle safety and emission functions including the following types of functions: (1) the fuel gauge readings may be incorrect; (2) a stuck fuel-level sensor may not be displayed in the instrument cluster; (3) the obd system may cause the check engine light to illuminate incorrectly; and, (4) the speedometer may be out of tolerance. Consequence: in the event of a vehicle crash, the electrical fuel pump may not receive a crash signal that is required for the fuel pump to disconnect and prevent future fuel delivery as designed. Action: dealers will recode the scn free of charge. the recall began on august 30, 2008. owners may contact mercedes-benz at 1-800-367-6372. Recall Date: 07/07/2008 | |
| 2004 MERCEDES SLK Manufactured between: 11/01/1996 and 04/30/2004 Defect: on certain passenger vehicles, failure of one of the side brake lights can occur. the base of the socket can be subject to thermal deformation over time. Consequence: this deformation can cause movement in the socket-to-bulb connection, which could lead to a loosening of the electrical contacts in the socket, and failure of the bulb to illuminate. Action: dealers will replace the rear lamp modules. the recall began on september 12, 2006, to approximately 8,200 owners. phase ii mailing is schedule on or about november 3, 2006, and phase iii mailing is schedule for january 2007 for the remaining owners. owners of vehicles with the updated trim (post-face lift) will get an interim notice during november 2006, asking them to schedule an appointment for rear tail lamp replacement later in 2007. however, if they experience an actual rear lamp failure before they receive that notice, they should come to their dealer immediately for a free repair. owners may contact mercedes-benz at 1-800-367-6372. Recall Date: 11/01/2005 | |
| SLR MCLAREN RECALLS | Top |
| 2006 MERCEDES SLR MCLAREN Manufactured between: 10/01/2003 and 05/31/2006 Defect: on certain passenger vehicles, under hard operating conditions, the engine compartment temperature can increase to a level which exceeds the design parameters for the alternator to not function and it will become damaged. Consequence: this will create the potential for an engine compartment fire. Action: dealers will improve the engine compartment and alternator cooling, install a modified control unit and a new alternator free of charge. the recall began on june 23, 2006. owners may contact mercedes benz at 1-800-367-6372. Recall Date: 06/19/2006 | |
| 2005 MERCEDES SLR MCLAREN Manufactured between: 10/01/2003 and 05/31/2006 Defect: on certain passenger vehicles, under hard operating conditions, the engine compartment temperature can increase to a level which exceeds the design parameters for the alternator to not function and it will become damaged. Consequence: this will create the potential for an engine compartment fire. Action: dealers will improve the engine compartment and alternator cooling, install a modified control unit and a new alternator free of charge. the recall began on june 23, 2006. owners may contact mercedes benz at 1-800-367-6372. Recall Date: 06/19/2006 | |
| ACURA | AUDI | BMW | BUICK | CADILLAC | CHEVROLET | CHRYSLER | DODGE | FORD | GMC | HONDA | HUMMER | HYUNDAI | INFINITI | JAGUAR | JEEP | KIA | LEXUS | LINCOLN | MAZDA | MERCEDES | MERCURY | MITSUBISHI | NISSAN | OLDSMOBILE | PONTIAC | SAAB | SATURN | SUBARU | SUZUKI | TOYOTA | VOLKSWAGEN | VOLVO |
Recall reports are furnished as a courtesy to our customers and are not represented as complete, definitive or authoritative. |
Copyright ©2010 Ikon Auto |
|
Site Management: Fabien Vegas Corporation
|